We sell only genuine Ridgid ® parts.
Enter Your Model Number
Popular Categories
Ridgid Replacement Parts by Category
-
![]()
Air Compressor Parts -
![]()
Band Saw Parts -
![]()
Circular Saw Parts -
![]()
Collated Screwdriver Parts -
![]()
Cordless Drill Parts -
![]()
Cut-Off Saw Parts -
![]()
Die Head Parts -
![]()
Drain Cleaner Parts -
![]()
Drill Press Parts -
![]()
Electric Drill Parts -
![]()
Foot Switch Parts -
![]()
Generator Parts -
![]()
Grinder Parts -
![]()
Hammer Drill Parts -
![]()
Impact Driver Parts -
![]()
Impact Wrench Parts -
![]()
Jig Saw Parts -
![]()
Jointer / Planer Parts
Ridgid Repair Articles
| How to Maintain a 2-Cycle Handheld Leaf Blower | How to Maintain a 2-Cycle Handheld Leaf Blower |
 | |
| Maintain your leaf blower. Step-by-step guide shows you how to rebuild the carburetor, replace the filters, and replace... | Maintain your leaf blower. Step-by-step guide shows you how to rebuild the carburetor, replace the filters, and replace... |
Commonly Purchased Parts
Popular Parts
2 are needed for the tools shown below
It is always best to replace both brushes, even if only one is worn.
Worn brushes frequently are the cause behind a motor running poorly.
Replacing brushes can fix a motor that’s operating intermittently.
New brushes can restore a motor’s electric braking.
Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.
it is sold individually.
Its purpose is to use 5 inch Hook and Loop 8 hole sandpaper attached to it.
To make the pad last longer do not put to much pressure on the sander when using it,the pressure will create heat and ruin the small hooks on the pad.
To replace the pad simply remove the four screws attaching it to the sander and replace it with a new pad.
If you would like to use a 5 inch 8 hole PSA (Pressure Sensitive Adhesive) pad, the part number is 300527003.
It is sold individually, 2 are needed to make a set.
Worn brushes frequently are the cause behind a motor running poorly.
• Replacing brushes can fix a motor that’s operating intermittently.
• Parts are sold individually
• New brushes can restore a motor’s electric braking.
Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power.
A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.
Its purpose it to hold the spool with line into the string head assembly.
To remove the Spool Cap press on the two tabs that lock it into the string head.
Ridgid Repair Articles
| How to Maintain a 2-Cycle Handheld Leaf Blower | How to Maintain a 2-Cycle Handheld Leaf Blower |
| |
| Maintain your leaf blower. Step-by-step guide shows you how to rebuild the carburetor, replace the filters, and replace... | Maintain your leaf blower. Step-by-step guide shows you how to rebuild the carburetor, replace the filters, and replace... |
