We sell only genuine Fein ® parts.
Enter Your Model Number
Popular Categories
Fein Replacement Parts by Category
Fein Repair Articles
| Quick Fix: How to Replace the Platen on a Belt Sander | How to Diagnose a Bad Power Cord or Switch |
 |  |
| Replacing the platen on a belt sander is a straightforward repair, but getting the fasteners back in place can be... | This article outlines the basics of power tool and appliance electrical diagnosis. You can use a multimeter to test... |
Same Day Shipping
Toll Free Support
Repair Help & Videos
Commonly Purchased Parts
See More
+
Popular Parts
Screw Set
Part Number: 43033087065
In Stock, 25+ available
$13.81
It is a genuine item that is supplied by the original equipment manufacturer for use with Fein power tools. This high-quality set includes one blade screw and two pad screws. Unfortunately, over time the threads may wear out or the part may simply get lost eventually requiring a replacement. Make sure to refer to the owner's manual of your model for the correct application of these components. You will need a properly sized screwdriver to secure or remove these screws.
Carbon Brush
This brush is sold individually, 2 are needed for the tools shown below
It is always best to replace both brushes, even if only one is worn.
Part Number: 30711129009
Backorder: No ETA
$7.21
Genuine fein replacement partThis brush is sold individually, 2 are needed for the tools shown below
It is always best to replace both brushes, even if only one is worn.
Worn brushes frequently are the cause behind a motor running poorly.
Replacing brushes can fix a motor that’s operating intermittently.
New brushes can restore a motor’s electric braking.
Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.
Speed Control Switch
Part Number: 30762412990
In Stock, 25+ available
$80.24
This is a Genuine Manufacturer Sourced replacement part used on some Fein Multi Master Oscillating Tools. This item is Sold Individually. Switches are commonly replaced parts in power tools, handling on/off and variable speed operations and is 100-120 volts. Because switches use mechanical internals, they will degrade and wear out over time, eventually requiring replacement.
Carbon Brush
Carbon brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. It is recommended to replace both brushes at the same time.
You would need a screwdriver and pliers to complete this job.
• First remove screws holding the cover together
• Separate two (2) halves of the housing to gain access to armature and brush holder
• Remove the old brush
• Install the new brush
• Reassemble and test your tool
Part Number: 30711062001
In Stock, 25+ available
$6.51
This is a manufacturer sourced replacement part used on a Fein grinders/sanders. It includes one (1) carbon brush with lead wire attached.Carbon brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. It is recommended to replace both brushes at the same time.
You would need a screwdriver and pliers to complete this job.
• First remove screws holding the cover together
• Separate two (2) halves of the housing to gain access to armature and brush holder
• Remove the old brush
• Install the new brush
• Reassemble and test your tool
Carbon Brush
Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.
Part Number: 30711168000
In Stock, 25+ available
$7.89
Genuine Manufacturer Sourced replacement part used on certain Fein Angle Grinders/Polishers. This item includes One (1) Carbon Brush with Lead Wire Attached.Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.
Fein Repair Articles
| Quick Fix: How to Replace the Platen on a Belt Sander | How to Diagnose a Bad Power Cord or Switch |
| |
| Replacing the platen on a belt sander is a straightforward repair, but getting the fasteners back in place can be... | This article outlines the basics of power tool and appliance electrical diagnosis. You can use a multimeter to test... |
Customer Comments
Thank you for a well developed, easy to use site.
James K.
Missouri, USA
