
We Sell Only Genuine Ridgid® Parts.
Ridgid Nailer Parts & Models
Popular Ridgid Nailer Parts

This is an authentic replacement piston ring. It is commonly used with Ridgid nailers/staplers. This item is supplied directly from original equipment manufacturer. A worn or broken piston ring will allow combustion gases to escape the seal and enter the crankcase. This would cause low compression and a loss of power. If compression is reduced significantly, the engine will not run at all. This part is made out of metal and is sold individually.
To complete this repair you will need a set of wrenches, pliers and a screwdriver.

This is a genuine Ridgid replacement part, it is sold individually.
The No-Mar Pad is attached to end of the safety to prevent the material that it is being used on from getting marred or dented by the safety arm.
It is a advisable to have one or two extra pads on hand as they do have a tendency to crack and deteriorate over time.

It is an authentic OEM item which is made for use with Ridgid coil roofing nailers. The collar is utilized to provide an air-tight seal for the top cap. Unfortunately, over time it may wear out and begin to crack eventually requiring a replacement to ensure your tool operates properly. Make sure to refer to the appropriate diagrams of your model for the correct installation. It is a high-quality collar which is made of durable rubber material and is sold as an individual component. You will need a wrench set to take the tool apart and replace this part.

This is a genuine OEM approved replacement part designed for Ridgid nailer. The Piston/Driver Assembly is the part of the nail gun that drives the nail into the material that is being used. To help extend the life of a pneumatic tool use the specified oil in it daily 4-5 Drops will do every time you use it. The Piston/Driver Assemblies do have a tendency to bend or break if not used correctly or if you are driving nails into extra hard material. This item is made out of Metal and it is Sold Individually.
To replace this part you would need a Wrench set.
• First you want to remove 4 screws from cap
• Remove the cap
• Remove driver, remove piston ring and o-ring
• Secure the o-ring and piston ring on new driver
• Install new driver
• Reattach the cap with the 4 screws

This is a genuine Ridgid replacement part, it is sold individually.
The No-Mar Pad is attached to end of the trip assembly to prevent the material that it is being used on from getting marred or dented by the trip assembly.
It is a advisable to have one or two extra pads on hand as they do have a tendency to crack and deteriorate over time. And get lost.

This is genuine manufacturer sourced replacement no mar pad. It is supplied from original manufacturer for use with Ridgid nailers. Nose cap is attached to the pushing lever to prevent the material from getting marred or dented. This pad is made out of plastic material and it is sold individually.
Replacing this item is very easy and it does not require any tools. Simply slide the pad on the safety element tip.

This is an authentic replacement piston ring. It is commonly used with Ridgid nailers/staplers. This item is supplied directly from original equipment manufacturer. A worn or broken piston ring will allow combustion gases to escape the seal and enter the crankcase. This would cause low compression and a loss of power. If compression is reduced significantly, the engine will not run at all. This part is made out of metal and is sold individually.
To complete this repair you will need a set of wrenches, pliers and a screwdriver.

This is a genuine Ridgid replacement part, it is sold individually.
The No-Mar Pad is attached to end of the safety to prevent the material that it is being used on from getting marred or dented by the safety arm.
It is a advisable to have one or two extra pads on hand as they do have a tendency to crack and deteriorate over time.

It is an authentic OEM item which is made for use with Ridgid coil roofing nailers. The collar is utilized to provide an air-tight seal for the top cap. Unfortunately, over time it may wear out and begin to crack eventually requiring a replacement to ensure your tool operates properly. Make sure to refer to the appropriate diagrams of your model for the correct installation. It is a high-quality collar which is made of durable rubber material and is sold as an individual component. You will need a wrench set to take the tool apart and replace this part.

This is a genuine OEM approved replacement part designed for Ridgid nailer. The Piston/Driver Assembly is the part of the nail gun that drives the nail into the material that is being used. To help extend the life of a pneumatic tool use the specified oil in it daily 4-5 Drops will do every time you use it. The Piston/Driver Assemblies do have a tendency to bend or break if not used correctly or if you are driving nails into extra hard material. This item is made out of Metal and it is Sold Individually.
To replace this part you would need a Wrench set.
• First you want to remove 4 screws from cap
• Remove the cap
• Remove driver, remove piston ring and o-ring
• Secure the o-ring and piston ring on new driver
• Install new driver
• Reattach the cap with the 4 screws

This is a genuine Ridgid replacement part, it is sold individually.
The No-Mar Pad is attached to end of the trip assembly to prevent the material that it is being used on from getting marred or dented by the trip assembly.
It is a advisable to have one or two extra pads on hand as they do have a tendency to crack and deteriorate over time. And get lost.

This is genuine manufacturer sourced replacement no mar pad. It is supplied from original manufacturer for use with Ridgid nailers. Nose cap is attached to the pushing lever to prevent the material from getting marred or dented. This pad is made out of plastic material and it is sold individually.
Replacing this item is very easy and it does not require any tools. Simply slide the pad on the safety element tip.