We Sell Only Genuine Ridgid® Parts.
Ridgid Miter Saw Parts & Models
Popular Ridgid Miter Saw Parts
This is a genuine Ridgid replacement part, it is sold individually.
2 are needed for the tools shown below
It is always best to replace both brushes, even if only one is worn.
Worn brushes frequently are the cause behind a motor running poorly.
Replacing brushes can fix a motor that’s operating intermittently.
New brushes can restore a motor’s electric braking.
Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.
Genuine Ridgid replacement part, it is sold individually.
This is part of the lower guard raising and lowering system.
As you raise and lower the miter saw the link actuator will ride on this bearing, making the action of this movement smooth and effortless.
This is a genuine Ridgid replacement part, it is sold individually.
It is used as part of the Actuator Link for the Lower Guard of the Miter Saws listed below.
Its purpose is to make the operation of the link and guard smooth and effortless.
This part does wear,it may be a good idea to order an extra one for future use.
This Kerf board is a genuine Ridgid replacement part., it is sold individually.
2 are needed to complete the set.
It is plastic and has 3 screw holes to secure it to your saw.
Kerf plates (also called kerf boards) are used to prevent excessive splintering, resulting in cleaner cuts. Using a worn or broken kerf board in your tool can result in a rough edge to the material you’re cutting.
This is a genuine Ridgid replacement part, it is sold individually.
This is an essential part of the lower guard return assembly. If it becomes bent or worn the lower guard will not retract as it was made to.
For safety purposes if this part is damaged it must be replaced.
Genuine Ridgid replacement part.
• Worn brushes are often the cause of a poorly running motor
• Replacing brushes can fix an intermittent motor
• New brushes can restore a motor’s electric braking
Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.
This is a genuine Ridgid replacement part, it is sold individually.
2 are needed for the tools shown below
It is always best to replace both brushes, even if only one is worn.
Worn brushes frequently are the cause behind a motor running poorly.
Replacing brushes can fix a motor that’s operating intermittently.
New brushes can restore a motor’s electric braking.
Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.
Genuine Ridgid replacement part, it is sold individually.
This is part of the lower guard raising and lowering system.
As you raise and lower the miter saw the link actuator will ride on this bearing, making the action of this movement smooth and effortless.
This is a genuine Ridgid replacement part, it is sold individually.
It is used as part of the Actuator Link for the Lower Guard of the Miter Saws listed below.
Its purpose is to make the operation of the link and guard smooth and effortless.
This part does wear,it may be a good idea to order an extra one for future use.
This Kerf board is a genuine Ridgid replacement part., it is sold individually.
2 are needed to complete the set.
It is plastic and has 3 screw holes to secure it to your saw.
Kerf plates (also called kerf boards) are used to prevent excessive splintering, resulting in cleaner cuts. Using a worn or broken kerf board in your tool can result in a rough edge to the material you’re cutting.
This is a genuine Ridgid replacement part, it is sold individually.
This is an essential part of the lower guard return assembly. If it becomes bent or worn the lower guard will not retract as it was made to.
For safety purposes if this part is damaged it must be replaced.
Genuine Ridgid replacement part.
• Worn brushes are often the cause of a poorly running motor
• Replacing brushes can fix an intermittent motor
• New brushes can restore a motor’s electric braking
Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.
