Compatibility
This part is compatible with the following machines:
Products Compatibility
This item works with the following types of products:
- • Sander
Questions & Answers
Appears this part 300527002 should fit my Craftsman sander, correct??
phil
for model number Craftsman 315.279890
Hi Phil,
Thank you for your question. Yes, this would be the correct hook and loop disc assembly for your Craftsman sander. I hope this helps. Thank you and have a great day!
how far apart are the 4 holes used to screw on the velcro pad? My holes are 4 1/4" apart. I purchased a velcro pad elsewhere and the holes did not line up.
dan diamond
for model number tacklife 5"
Hi Dan,
Thank you for your question. The distance between the screw holes is approximately 1 inch apart. I hope this helps. Thank you and have a great day!
does the assembly come with the sticky velcro?
Dennis
Hello Dennis, Thank you for the question. This pad is held in place with screws. Hope this helps, good luck with this repair!
#1IS this a RANDOM orbital or just a Palm sander
#2 does it have variable speed?
And if so is there an adjustment on it?
James
for model number RS290
Hi James,
Thank you for your question. This is a Random Orbit Sander and it has no load speed (rotational speed, at no load). For more information on the sander, you will need to consult the owner's manual. Here is a link to the manual, http://manuals.ryobitools.com/system/files/6075/original/RS290_RS290G_172_trilingual_07.pdf?2018. I hope this helps. Thank you and have a great day!
Will this loop and hook 5 inch work on my 4 1/2in Ryobi lorbital sander RS-115. Is the hole pattern the same?
Charles
for model number RS-115
Hello Charles, Thank you for the question. This Hook and Loop Disc is for 5" and will not fit the 4.5". The holes will not line up. I looked up the part for your model number and it is listed as No Longer Available/Discontinued. There is no part substitutions listed. My suggestion here would be to call the manufacturer and see if they can provide you with a substitution for these part numbers. Hope this helps!
Will this work for model # Rs290?
Drew
for model number Rs290
Hello Drew, thank you for your question. Unfortunately, that part is not listed as a compatible replacement. The correct replacement hook and loop unit for your model is Hook and Loop Backing Pad Part Number: 030157001018. Good luck with your repair!
I need the hook and loop pad that holds the paper. I see prices of $7.00 each to $18.18 each?
Ron
for model number RS290
Hello Ron, Thank you for contacting us. I have researched the model you have provided and have found the part you?re looking for is Part Number: 030157001018. Thank you for your inquiry, good luck with this repair!
Will this fit my Ridgid sander?
Marcus Sucro
for model number R8606
Hello Marcus, thank you for inquiring! We are showing the correct part for your model is 300527008. We hope this helps, and have a great day!
My sandpaper doesn't stay in the sander, do I purchase the #300527002 ? Does that part come with the H&L to hold the new sandpaper?
Tom
for model number R2600
Hello Tom, Thank you for your inquiry. I have researched the model you have provided and have found the part you are looking for is 300527002. Good luck with your repair.
it says this is a 5" disk but the picture clearly shows a 4.5" disk. which is it?
brett
Hello Brett, thank you for your question. This is a 5 inch disk. I hope this helps.
Hello, Does this also replace same part on Craftsman model # 315.116950 orbital sander?
Harry C. Whalen
for model number 315.116950
Hello Harry, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is Part Number: 030157001018. Part number 300527002 is not listed as a compatible part. Hope this helps, good luck with this repair!
Need to replace the hook/loop backing pad. What is the difference between your p/n 300527002 ($7.18) and your p/n 030157001018 ($18.18).
Gary
for model number RS290 orbit sander
Hello Gary, Thank you for your question. 300527002 is 4.5 inches in diameter and part number 030157001018 is 5 inches. Hope this helps!
Your reply to my question is incorrect per your data sheet. 300527002 says it is 5 inch. And 030157001018 is also 5 inch. So why is ...7002 $7.18 and ...1018 $18.18? What is the difference between the two backing pads?
Gary
for model number RS290
Hello Gary, Thank you for contacting us. The Part Number: 030157001018 is the part listed for your model number RS290. RS290 is listed for the RS290G. They holes could line up different or be a different size. It is best to use the one listed for your model RS290. We base our prices on what we are charged by the manufacturer for the parts. The manufacture has different pricing so it effects our pricing. Hope this helps!
Repair Instructions: Submitted by Customers Like You
27 of 30 people found this instruction helpful
Tool Type:
Sander
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, N/A
Bad sanding loop assembly.
Removed 4 screws holding on the old pad. Blew out the saw dust from inside of the sander. Installed the new pad and screws.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
13 of 16 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Pad worn
The pad would no longer hold the sand paper..4 screws attached the pad to the sander, ..simply removed, pulled the bad pad off, attached the new one..took all of 2 min..sander back in action
Did you find this story helpful?
Thanks for voting and helping fellow customers!
7 of 7 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Sanding pad tore apart.
1 Took the screws out
2 Pad off
3 Pad on
4 Screws back in
5 Using sander
2 Pad off
3 Pad on
4 Screws back in
5 Using sander
Did you find this story helpful?
Thanks for voting and helping fellow customers!
7 of 8 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Pad wore out
Removed the 4 screws holding the pad to the base. Placed new pad on the base, lined up the screws holes, then attached the pad to the base with the screws.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Disc needed replacing
Unscrewed and removed broken disc
Placed with new disc and replaced screws
Placed with new disc and replaced screws
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Pad for holding hook and loop sand paper on sander ripped and separated
Turned sander upside down.
Unscrewed (4) screws holding old pad base on.Kept these screws.Removed old base.
Placed new base on sander,aligned screw holes of new base pad with sander screw thread holes replaced the (4) screws.Finished.
Unscrewed (4) screws holding old pad base on.Kept these screws.Removed old base.
Placed new base on sander,aligned screw holes of new base pad with sander screw thread holes replaced the (4) screws.Finished.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Hook and loop disc assembly brok
1). Removed the four machine screws from the hook and loop disc assembly.
2). Removed the old hook and loop disc assembly.
3). Inserted one of the machine screws into the recessed holes of the hook and loop disc assembly and loosely tightened it.
4). Aligned the remaining holes and inserted the remaining three machine screws.
5). Cross tightened each of the screws until all four were factory tight.
2). Removed the old hook and loop disc assembly.
3). Inserted one of the machine screws into the recessed holes of the hook and loop disc assembly and loosely tightened it.
4). Aligned the remaining holes and inserted the remaining three machine screws.
5). Cross tightened each of the screws until all four were factory tight.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Hook and loop disk split
Unscrewed torn disk and installed new one
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, None
Removed 4 small screws
Removed hook assembly
Set new assembly
Installed 4 screws
Finished
Removed hook assembly
Set new assembly
Installed 4 screws
Finished
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Normal wear and tear
Swapped out the part and good to go. Thanks!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
show more
Discussion
Discussion for Hook and Loop Disc Assembly - ( 300527002 )
Discussion is closed. To ask our experts a question about a part, use the Q&A feature.
Question: R2600 Sanding Pad Assembly
DThompson
The hook & loop pad is completely worn and needs to be replaced. Do I need part 41 a or 41b or both ( the $6 or $13 part)?
Hi DThompson,
You just need 41a 300527002 hook and loop replacement pad.The 41b is for glue on discs.Hope that helps.Good luck.
Tinker
You just need 41a 300527002 hook and loop replacement pad.The 41b is for glue on discs.Hope that helps.Good luck.
Tinker
Question: Help
tikidude
does this have micro fiber pad r2601 5" orbital sander
