Repair Parts Home    Power Tool Parts    Ryobi Parts    Ryobi Table Saw Parts    Ryobi BTS21 10" Table Saw Parts
Ryobi BTS21 10 ryobi logo

 Ryobi BTS21 10" Table Saw Parts

Page A
Page B
Page C
Page D
Page E
Page F
   Page A   

 Fig # Img Part Name Availability Price
A1
End Cap
End Cap
Part #: 0134010227
In stock
13 available
 $2.99
Add To Cart
A2
Miter Indicator
Miter Indicator
Part #: 0181010208-58
In stock
7 available
 $3.99
Add To Cart
A3
Miter Fence
Miter Fence
Part #: 0134011801
In stock
7 available
 $15.44
Add To Cart
A4
Locator Pin
Locator Pin
Part #: 0134010244
In stock
6 available
 $3.99
Add To Cart
A5
Screw (3/16 In. Pan HD.)
Screw (3/16 In. Pan HD.)
Part #: 410451702
In stock
13 available
 $2.99
Add To Cart
A6
Adjusting Knob
Adjusting Knob
Part #: 0181010209
In stock
5 available
 $3.99
Add To Cart
A7
Flat Washer (8 X 16 X 1.5T)
Flat Washer (8 X 16 X 1.5T)
Part #: 412011051
In stock
2 available
 $3.99
Add To Cart
A8
Miter Fence Holder
Miter Fence Holder
Part #: 0181010210
In stock
7 available
 $3.99
Add To Cart
A9
Hex Screw (5/16-18 X 3-1/4 In.)
Hex Screw (5/16-18 X 3-1/4 In.)
Part #: 410011717
In stock
4 available
 $3.99
Add To Cart

Enter your engine's type number in this search field to show the parts that match your engine.

Your engine's type number is the second part of the model number stamped on your Briggs & Stratton engine (see picture).

Saw Parts  Table Saw Parts

Repair Guides
Power Tool Care and Maintenance 101
Power Tool Care and Maintenance 101

This article suggests guidelines for power tool care and maintenance. It also describes information tools available at eReplacementParts.com.

How to Diagnose a Bad Power Cord or Switch

This video outlines the basics of power tool and appliance electrical diagnosis. You can use a multimeter to test tool and appliance cords and switches, the two parts usually responsible for electri...

Discussion
Discussion for the Ryobi BTS21 10" Table Saw

Post a Comment
Login or signup to comment.
Login or signup to comment.
Ask a question, answer a question, or post a comment!
  • Subject:
  •  
  • Comment:
  •  
Jennsgamma
Question: Fence

Jennsgamma

Can I get an entire new fence for BTS 21?
WJA
Reply: Fence

WJA

Hello Jennsgamma,

The Fence Assembly, part number 089110110701 for the Ryobi BTS21 Table Saw has not been available for a couple of years now. You may be find one if you keep searching online.

-WJA
1227220
Question: Dado Throat

leftyslim

Will the dado throat plate for the bts211 work on a bts21?
WJA
Reply: Dado Throat

WJA

Hello 1227220,

Since both saws use the same standard throat plate, part number 089110110003. The 0134010313 Dado Throat Plate, can be used on the BTS21. The Dado the manufacture specs out for both of these saws is a 6 inch stackable set, with a maximum cutting width of 5/8 inch. And do not use a wobble dado set on either of these saws.

-WJA
mar
Reply: Dado Throat

mar

Will the dado throat plate for the bts211 work on a bts15
how do you remove the arbor assembly?
waynej
Question: Wiring

waynej

Tell me which wire goes where 4 Posts and 4 wires
imp67ss
Reply: Wiring

imp67ss

With the switch facing to insert it in the square hole. The two white wires goes on the left side of the switch one on top and one on bottom. Two black wires go on the opposite side.
1544200
Reply: Wiring

1544200

Does it matter whether one or the other is on top or bottom?
WJA
Reply: Wiring

WJA

Hello 1544200,

It does not matter which one goes on top or bottom. As long as you wire it like imp67ss siad.

-WJA
casualron61
Question: Ryobi Table Saw Switch Ts21

casualron61

what wires go were
Tinkerdave
Reply: Ryobi Table Saw Switch Ts21

Tinkerdave

Hi casualron61,
I can't find a wiring diagram on that model. From the looks of it you should have a four pole switch with a black and white from the power cord and a black and white to the motor.Please confirm if this is right.
Tinker
cinderfella13
Question: Ryobi Table Saw Switch Replaceme...

cinderfella13

I am replacing the switch on my ryobi table saw. It has 4 wires - 2 white and 2 black. I need to know the correct order in which to attach them..


thanks
1118245
Reply: Ryobi Table Saw Switch Replaceme...

1118245

Request answer as how re-wire black and white wires on switch replacement part.
Roadhogg
Question: Ryobi Table Saw

Roadhogg

Need Help!!!!

I was sawing with this saw on Friday and in the middle of a cut it stopped just like i had turned it off. When i touched the motor it was not hot but i could smell a little something like hot wiring. I checked out the switch and it appears to be fine. What do i need to look at in the motor?

P.S. The motor will turn over free by hand.
Tinkerdave
Reply: Ryobi Table Saw

Tinkerdave

Hi Roadhogg,
It sounds like you have an break in the field.This can be caused by a lot of things but the fact you smell something burnt leads me to think that the saw got hot and burned the field out.The most important thing to remember on small table saws is to always keep sharp blades on them and blow out the motor housing after use as saw dust will build up in the housing and block air flow.Hope that helps.Good luck.
Tinker
ryobi_uk_warrenty_repair_centre
Reply: Ryobi Table Saw

ryobi_uk_warrenty_repair_centre

we get a lot of these returned at work
9 out of 10 times they get replaced
because the work that needs doing
is above ecconomical repair leval (ERL)

if your going to do the work yourself
watch for the spring that holds the motor in place
it bites lol :cool:
Does anyone know of another web site that sells Ryobi replacement parts?
The motor runs but it is not engaging the blade + it's noisy; I suspect the gears in the gearbox are stripped. What is the sequence to remove & replace the motor/gearbox?
Rodger
Question: BTS21 Portable Table Saw

Rodger

I Recenty bought this model from a local Home Depot at a cut rate because it was a floor model at one time. It came without the Rip Fence & assembly as well as the Miter Fence & assembly. Does anyone have these two (2) parts for sale?
How do I remove the armature from subject motor? I have separated the Arbor Jackshaft Assembly. I have removed the Brushes but not the Brush Holder Tubes. The Armature resists removal with jiggling and wiggling. Do the Brush Holder Tubes have to be removed? If so, how?

Jim
WJA
Reply: Armature Removal-BTS21 Ryobi Tab...

WJA

Hello Jim,

The armature is most likely being held by the motor housing and commutator end bearing. If you have been able to remove the gear box from the armature, lightly tap on the open end of the motor housing (alternating opposite sides) and the armature will come out. Make sure the armature doesn't get damaged when it comes out. If the gear box is still on the armature with a little tap or two (lightly) it will come off easily also.

Good luck,
WJA
jhalepaska
Question: A134010104 Motor Assembly

jhalepaska

Does this item include the Arbor Assembly?
WJA
Reply: A134010104 Motor Assembly

WJA

Hello jhalepaska,

In answer to your question regarding the A134010104 motor. The arbor assembly is included when you purchase the motor.

WJA
LeRoy Beukema
Question: Motor

LeRoy Beukema

What is the easiest way to remove the motor on BTS21 and replace the bearings?
kevin
Question: Dado

kevin

Model bts211 10" Ryobi table saw--I need accessories to dado. Per instruction book, I need special throat plate, 6" stacked 5/8" max dado. Where do I get them? Home Depot said they must be bought online...
William (Bill) Bush
Question: Inspection Of Parts Of The Motor...

William (Bill) Bush

I think I stated most of my problems above.
kev
Question: Ryobi Table Saw

kev

How do you remove the needle bearing from the blind hole in the gear housing for the main shaft?
bob
Question: Kickback

bob

after a kickback the saw now is loose and sounds loud, like bad bearings. any ideas please.
ev10ss
Reply: Kickback

ev10ss

I just had the same thing happen to me. Were you able to determine what the problem was?
buppiex
Reply: Kickback

buppiex

This happened to me tonight (3 Sep 2011). The saw is not loose, but it's noisy while running, but very noisy when you turn it off and it coasts to a stop. I will start the dis-assembly tomorrow and feed back my findings. It's probably either failed bearings or a bent armature shaft.
gene
Question: Bts21

gene

where can i find a service center for this table saw, i live in lake elsinor,calid 92595
lee
Review: Ryobi - BTS21
5 star
lee
I have had the tool for approx 2 years. I used it in my construction company. I would recommend, and also buy another one.
djduby
Review: Ryobi - BTS21
5 star
djduby
very good saw more power then saws withhigher price tag
Accessories
Accessories for the BTS21

Standard Saw Blades:
See more standard saw blades 

10" 5/8" Arbor 36 Tooth Table Saw Blade
$27.78

PRO1060CHB
10" TCG 5/8" Arbor 60 Tooth Table Saw Blade
$125.61

DW7662
10" ATB 5/8" Arbor 80 Tooth Table Saw Blade
$107.95

fancyboxy