We Sell Only Genuine Black and Decker® Parts.
Black and Decker Hammer Drill Parts & Models
Popular Black and Decker Hammer Drill Parts
This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the new cord wires to go correctly into wire terminals also routing the cord and wires in the right path can help avoid pinching when the tool case (Plate) is put back into place.
This cord protector is a genuine DeWalt replacement part and is sold individually.
Cord Protectors are designed to slide onto your cord and fit securely at the end, where it’s firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.
This screw is a genuine Dewalt chuck screw. It is constructed of tough steel for long life. It has a beveled head with torx drive for a secure fit. This screw is reverse thread for securing drill chucks. It also has locking compound within the threads for an even tighter installation.
This screw is commonly found in Dewalt cordless drills and it is compatible with the tools listed below. It is not guaranteed to fit any other power tools.
This Ball Bearing has metal shielding on both sides. This is a genuine Dewalt replacement part that is sold individually.
• Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly.
• Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.
This switch is a genuine Dewalt replacement switch. This part is commonly found in Dewalt cordless tools and it is an exact replacement for an existing switch. Over time and because of use a switch will deteriorate and eventually fail. This switch will repair the switching and variable speed functions caused by a failed switch. This switch is manufactured by Dewalt and it is a high quality, heavy-duty switch.
This part is compatible with the models listed below, but it is not guaranteed to fit any other power tool models.
This carbon brush is an authentic DeWalt replacement part.
It is sold individually, 2 are needed to make a set
• Worn brushes are frequently the cause of a poorly running motor.
• Replacing brushes can fix an intermittently operating motor.
• New brushes can restore a motor’s electric braking.
Carbon motor brushes are one of the most commonly replaced power tool parts.
The reason is that carbon brushes are wear items, meaning that through friction and use they will gradually wear away and eventually will need replacing.
Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power.
A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned.
When replacing carbon brushes, also check your armature for burns, cracks, or other damage which are indications of a larger motor problem needing attention.
This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the new cord wires to go correctly into wire terminals also routing the cord and wires in the right path can help avoid pinching when the tool case (Plate) is put back into place.
This cord protector is a genuine DeWalt replacement part and is sold individually.
Cord Protectors are designed to slide onto your cord and fit securely at the end, where it’s firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.
This screw is a genuine Dewalt chuck screw. It is constructed of tough steel for long life. It has a beveled head with torx drive for a secure fit. This screw is reverse thread for securing drill chucks. It also has locking compound within the threads for an even tighter installation.
This screw is commonly found in Dewalt cordless drills and it is compatible with the tools listed below. It is not guaranteed to fit any other power tools.
This Ball Bearing has metal shielding on both sides. This is a genuine Dewalt replacement part that is sold individually.
• Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly.
• Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.
This switch is a genuine Dewalt replacement switch. This part is commonly found in Dewalt cordless tools and it is an exact replacement for an existing switch. Over time and because of use a switch will deteriorate and eventually fail. This switch will repair the switching and variable speed functions caused by a failed switch. This switch is manufactured by Dewalt and it is a high quality, heavy-duty switch.
This part is compatible with the models listed below, but it is not guaranteed to fit any other power tool models.
This carbon brush is an authentic DeWalt replacement part.
It is sold individually, 2 are needed to make a set
• Worn brushes are frequently the cause of a poorly running motor.
• Replacing brushes can fix an intermittently operating motor.
• New brushes can restore a motor’s electric braking.
Carbon motor brushes are one of the most commonly replaced power tool parts.
The reason is that carbon brushes are wear items, meaning that through friction and use they will gradually wear away and eventually will need replacing.
Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power.
A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned.
When replacing carbon brushes, also check your armature for burns, cracks, or other damage which are indications of a larger motor problem needing attention.
