We Sell Only Genuine Rolair® Parts.
Rolair Compressor Parts & Models
Popular Rolair Compressor Parts
This is a genuine OEM sourced replacement part used on Rolair air compressors. Its purpose is to filter out dust and debris from contaminating the engine. This filter is made out of paper, plastic and metal. This item is sold individually.
To replace this filter no tools are needed. Simply remove the wing nut that secures the air cleaner cover and replace the filter element.
This is a genuine OEM approved replacement part designed for use with Rolair compressors. The pressure switch is a mechanism which communicates to your compressor when to stop and when to start building up pressure. There are multiple reasons a pressure switch could be leaking air.
To complete this repair you would need: wrench set, nut driver set and a thread-sealing tape.
• Shut off the electricity and drain the air tank
• Remove the tank pressure gauge
• Remove the pressure switch tube
• Remove the pressure regulator assembly
• Disconnect the wires
• Remove the safety valve
• Install the new pressure switch
• Reinstall the safety valve
• Connect the wires
• Reinstall the pressure switch tube
• Screw the pressure gauge onto the new pressure switch and tighten the gauge firmly
• Test the air compressor
Pilot Unloader Valve - 1/4" Tube, Pilot 1/4" M NPT
This OEM sourced replacement gauge is designed for use with Rolair compressors. The gauge registers pressure readings and allows you to maintain needed pressure. This gauge is sold individually.
You would need a wrench to secure this gauge to the manifold. When replacing this item make sure to unplug the air compressor and bleed out air from the tank.
This is a genuine OEM sourced replacement isolator foot that help to keep you air compressor stable and also help to minimize the vibration. This item is made out of rubber with metal and it is sold individually. Please note the screw used to attach it is sold separately.
You would need a wrench to replace this item.
This rubber foot is genuine OEM, guaranteed to fit Rolair compressors listed below. These anti-vibration feet are an important part of dampening the machine's sound. Since sound reduction only occurs if all feet are attached, owning a few backup feet is recommended. This repair does not require any tools; just push the part into place. Includes one (1) foot.
This is a genuine OEM sourced replacement part used on Rolair air compressors. Its purpose is to filter out dust and debris from contaminating the engine. This filter is made out of paper, plastic and metal. This item is sold individually.
To replace this filter no tools are needed. Simply remove the wing nut that secures the air cleaner cover and replace the filter element.
This is a genuine OEM approved replacement part designed for use with Rolair compressors. The pressure switch is a mechanism which communicates to your compressor when to stop and when to start building up pressure. There are multiple reasons a pressure switch could be leaking air.
To complete this repair you would need: wrench set, nut driver set and a thread-sealing tape.
• Shut off the electricity and drain the air tank
• Remove the tank pressure gauge
• Remove the pressure switch tube
• Remove the pressure regulator assembly
• Disconnect the wires
• Remove the safety valve
• Install the new pressure switch
• Reinstall the safety valve
• Connect the wires
• Reinstall the pressure switch tube
• Screw the pressure gauge onto the new pressure switch and tighten the gauge firmly
• Test the air compressor
Pilot Unloader Valve - 1/4" Tube, Pilot 1/4" M NPT
This OEM sourced replacement gauge is designed for use with Rolair compressors. The gauge registers pressure readings and allows you to maintain needed pressure. This gauge is sold individually.
You would need a wrench to secure this gauge to the manifold. When replacing this item make sure to unplug the air compressor and bleed out air from the tank.
This is a genuine OEM sourced replacement isolator foot that help to keep you air compressor stable and also help to minimize the vibration. This item is made out of rubber with metal and it is sold individually. Please note the screw used to attach it is sold separately.
You would need a wrench to replace this item.
This rubber foot is genuine OEM, guaranteed to fit Rolair compressors listed below. These anti-vibration feet are an important part of dampening the machine's sound. Since sound reduction only occurs if all feet are attached, owning a few backup feet is recommended. This repair does not require any tools; just push the part into place. Includes one (1) foot.
