Repair Forum     Repair Center    Blog
Sign In Support Shopping Cart
      Call us toll free 866-802-6383
8:00AM-10:00PM Mon-Fri, ET
9:00AM-8:00PM Sat, ET
Repair Parts Home    Power Tool Articles    How to Remove a Stuck Drill Chuck

Why Read This Article?

  • Alternative repair steps.
  • Overcome common setbacks.
  • Professional repair video.

Article Breakdown

  • Use these alternative repair steps for difficult chucks!
  • These steps pertain to keyless chucks only.

How to Separate a Chuck Collar from a Drill Chuck

  • Drills with broken gearboxes often break with the chuck collar still attached to the chuck.

1. Remove the snap ring.

2. Press the chuck and spindle out.

How to Remove a Drill Chuck from its Arbor Shaft

1. Flatten the shaft with a grinder.

2. Use a vise to remove the chuck screw.

3. Tighten an Allen key into the chuck.

4. Turn the Allen key.

Tips to Remove a Stuck Chuck Screw

Tip #1- Heat the arbor shaft.

Tip #2- Use a wrench for leverage.

Tip #3- Strike the chuck screw.

Video


Tools & Materials

  • a screwdriver that fits your drill's chuck screw
  • a pair of snap ring pliers
  • a vise

(and possibly)

  • a wrench
  • a press
  • a blowtorch

How to Remove a Stuck Drill Chuck

August 12, 2010
« Previous Article
Broken gearboxes and sticky chuck screws can make removing a drill chuck difficult. This article explains the tricks you need to overcome these common repair setbacks.

Most drill chucks come off their drills using normal chuck removal methods, like the chuck removal steps we offer in our article, "How to Remove a Drill Chuck."

Drill With Broken Gearbox

However, drill chucks can be difficult to remove for a number reasons that require an extra trick or two to get the job done.

The steps and suggestions below explain how to remove keyless drill chucks from drills with broken gear boxes. We also explain how to remove sticky chuck screws.

See this article's repair video for a professional demonstration!

 

How to Separate a Chuck Collar from a Drill Chuck

Our example drill in this article came into the shop with its gearbox already broken.

In cases like these, drill chucks usually come off the drill with the arbor shaft and chuck collar still attached to the chuck. The first step to remove the chuck then is to first take its collar off.

 

1. Use a pair of snap ring pliers to remove the snap ring.

Getting that snap ring out will allow the chuck collar to pop off when we press it off of the chuck.

Remove Snap Ring

 

2. Press the chuck out with a shop press.

Position the drill chuck collar between clam shells for support, align a punch on the chuck's arbor shaft, and then press it out.

Press the Arbor Shaft Out of the Chuck Collar

Pressing the arbor shaft will take the drill chuck with it, leaving the chuck's lower collar behind.

[Back to top]

 

How to Remove a Drill Chuck from its Arbor Shaft

With its collar removed, it's now time to separate the drill chuck from its arbor shaft.

 

1. Flatten the arbor shaft with a grinder and grinding wheel.

The arbor shaft must be placed into a vise in order to remove the chuck screw. The shaft will have to be made flat on at least two sides to accommodate the vise.

Be careful to avoid touching the arbor shaft while it is still hot.

Grind the Arbor Shaft Flat

 

2. Secure the flattened chuck spindle in a vise and unscrew the chuck screw.

Remember that chuck screws are reverse threaded, so you must turn them in the direction of the drill's forward position. 

Place in Vise and Turn the Chuck Screw

Because chuck screws are usually held into position with loctite, it often takes a lot of force to turn them.

 

3. Tighten a large Allen key into the chuck.

Place Large Allen Key in Chuck

 

4. Turn the Allen key to spin the chuck off the arbor shaft.

Turn the Allen key in the direction of the drill's forward rotation (like the chuck screw).

Use a Bar to Turn the Key

Unscrewing the chuck is easy with the help of a "cheater bar."

[Back to top]

 

Tips to Remove a Stuck Chuck Screw

Chuck screws can be very difficult to unscrew every now and then. This usually happens when manufacturers use too much loctite to affix it to the drill's arbor shaft.

Follow the professional repair tips below for to remove a stuck chuck screw.

 

Tip #1- Heat the arbor shaft.

Use a blowtorch on the arbor shaft to loosen up the loctite on the chuck screw. This is the best way to loosen the screw in most cases.

Heat the Arbor Shaft with a BlowtorchArbor

Really tough chuck screws may require more than one heating.


Tip #2- Use a wrench for leverage.

If the screwdriver you're using to turn the chuck screw has a square shaft, you can attach a small wrench to it for some extra leverage.

Use a Wrench for Leverage

 

Tip #3- Strike the chuck screw with a screwdriver and hammer.

Carefully position your screwdriver on the chuck screw and gently strike its end with a hammer to loosen the screw's loctite bond.

This should be considered a last-resort method since it risks destroying the chuck if done incorrectly.

[Back to top]

 

Conclusion

To get started with your home tool repair, visit our Drill Parts page to find your drill model's replacement drill chuck.

We're dedicated here at eReplacementParts.com to get tool owners the parts and know-how they need that will save them time and money. 

Visit us again for professional tips that will get you past the snags in your own repairs!

 

[Back to top]

What we're about.

« How to Install a Locked Chainsaw Sprocket Plate
fancyboxy