Tools & Materials
Power cord cracked? It's time to face the fix. Whether you are a master carpenter or a seasonal sander, eReplacementParts.com provides the parts, procedures and facts you need to fearlessly fix what fails you.
The cord protector (also called the strain relief or reliever) covers the first few inches of the power cord where it enters the sander. Its purpose is to prevent the power cord from bending or kinking, which can cause cracks to develop along the insulation. Eventually, the cord protector will dry out and become cracked itself. The cord protector should be replaced as soon as damage is detected.
Replacing the component is easy to do, and this simple repair will protect your sander (and your wallet) from sustaining further damage. This article provides step-by-step instructions for removing and installing the cord protector on a Porter Cable Quicksand 333 series sander.
Let's get started.
REMOVING THE CORD PROTECTOR [top] 1. Remove the sanding pad.
Remove the (3) screws from the sander pad.
Remove the sanding pad from the sander.
2. Remove the clutch belt.
Remove the clutch belt from the fixed pulley and the pad support pulley.
3. Remove the pad housing.
Remove the (2) screws from the pad housing.
Separate the two halves of the pad housing.
Separate the sander from the pad housing.
4. Remove the housing O-ring.
Use a screwdriver to pry the O-ring out of the groove in the housing.
Work around the edges of the O-ring; stretching it around the pad support assembly as you move.
Remove the O-ring from the sander.
5. Remove the pad support.
Grasp the fan to prevent the pad support from rotating.
Remove the (1) screw from the pad support.
Remove the pad support (and washer) from the sander.
6. Remove the fan.
Slide the fan assembly off the spindle and away from the sander.
7. Split the motor housing.
Remove the (4) screws from the motor housing.
Remove the top half of the motor housing.
8. Remove the cord protector.
Disconnect the white wire (containing the flag terminal) from the motor brush.
Lift the switch (and the black wire) out of the motor housing.
Loosen the screw that secures the black wire to the switch.
Disconnect the black wire from the switch.
Remove the power cord from the sander.
Remove the cord protector from the power cord.
INSTALLING THE NEW CORD PROTECTOR [top] 9. Install the cord protector.
Carefully bend the flag terminal (on the white wire) approximately 90 degrees (this will facilitate installation of the cord protector).
Slide the new cord protector over the two wires and onto the power cord. (Rotating the cord protector as you slide it over the wires will help prevent the flag terminal from binding).
REASSEMBLING THE UNIT [top] 10. Reinstall the power cord.
Install the black wire into the switch.
Secure the black wire to the switch with the screw.
Connect the white wire (the flag terminal) to the motor brush.
11. Tuck the wires.
Install the switch assembly into the recess in the motor housing.
Tuck the black wire into the channel along the top of the motor housing.
Install the cord protector into the recess in the motor housing.
Tuck the insulated portion of the power cord (containing both sets of wires) into the channel in the motor housing.
Tuck the white wire into the channel in the motor housing.
12. Reinstall the top half of the motor housing.
Install the rubber bumper into the recess on the motor housing.
Visually inspect the wires for potential pinch-points; adjust the wires as necessary.
Install the top half of the motor housing.
Secure the motor housing with the (4) screws.
13. Reinstall the fan.
Slide the fan onto the spindle.
14. Reinstall the pad support.
Install the pad support onto the sander.
Install the washer onto the pad support. (The side with the recess should be facing away from the bearing).
Secure the pad support with the (1) screw.
15. Reinstall the housing O-ring.
Install the housing O-ring into the groove on the motor housing.
16. Reinstall the pad housing.
Install one half of the pad housing onto the sander (the seam should align with the seam on the motor housing).
Install the second half of the pad housing onto the sander.
Secure the pad housing with the (2) screws.
17. Reinstall the clutch belt.
Install the clutch belt onto the fixed (small) pulley.
Stretch the clutch belt onto one side of the pad support.
Rotate the pad support to seat the clutch belt.
18. Reinstall the sanding pad.
For easy alignment: Pass a small screwdriver through one of the screw holes on the sander pad; then insert the end of the screwdriver into one of the holes on the pad support.
Install the sanding pad.
Secure the sander pad with the (3) screws.
Sanding can be a demanding task. But you don't have to rough-up your accountant to smooth-out your countertops. As you just learned, repairing your own power tools is simple when you follow our step-by-step guides. Not only did you expand sander functionality at a fraction of the cost of replacement; you have taken the edge off all future repairs.