Pool and Spa Parts
Search By Pool and Spa Model or Part Number
Same Day Shipping
Toll Free Support
Repair Help & Videos
Pool and Spa Parts Repair Articles
How to Fix a 2-Cycle Engine Carburetor | How to Fix a Lawn Mower Carburetor |
This article will walk you step-by-step through the process of repairing a 2-Cycle... | This article will help teach you the process of properly maintaining and repairing a lawn mower carburetor.... |
Same Day Shipping
Toll Free Support
Repair Help & Videos
Popular Pool and Spa Models
Most Popular Pool and Spa Replacement Parts
Pool and Spa Infinite Switch Large Element
5 Reviews
In Stock
Part Number: 316436001
$51.00
This infinite burner switch, also commonly known as a surface element control switch is a genuine OEM replacement part used in electric ranges/cooktops. It is 240V and designed for an 8-inch surface element. The switch controls the heating of the surface element and turns it on/off as needed. If you have noticed that your range is not heating at all, or it is overheating, and you have difficulties switching off the appliance, then you will likely need to replace the burner switch. Disconnect the range from the power source to before beginning the repair. Pull off the control knob and detach the back panel to access the switch. Disconnect the wire connectors from the old switch and remove the screws that hold it in place. It is recommended to take a picture of how the wires are routed for the installation. Place the new burner switch in the mounting position and reconnect the wires to the new switch. Secure it with the appropriate fasteners and reattach the back panel. Place the control knob back on and reconnect the range to the power source.
Pool and Spa Oven Heating Element
10 Reviews
In Stock
Part Number: 316075103
$23.88
The Oven Bake Element is a black, metal part which supplies heat to the oven. This element is 19-1/2" wide x 18-1/2" long and has 3-1/2" inserts. It is rated as "Easy" to install by users, and attaches to the bottom of the oven. If you notice visible damage, or that your oven is not receiving heat properly then it may be a problem with this part. Check your model number and user manual to see if this is the right part for you. It is important for you to disconnect your appliance from the power source before performing this repair. After disconnecting your appliance, remove the two screws/nuts connecting the old element, pull it out, and discard if faulty. Simply connect the new element prongs where the old element fit, and screw it back in.
Pool and Spa O-ring
In Stock
Part Number: 16Y425
$18.69
This O-ring, also known as a gasket, is a genuine OEM replacement part designed for use in air sprayers. It is a rubber seal with a diameter of approximately 1.5 inches, that sits between the pump and filter to prevent air and paint leakage between the two mating parts. If the ring is lost, worn out, damaged, or has lost elasticity, it will need to be replaced. A faulty O-ring will result in issues such as leaking, low pressure, inconsistent spray patterns, and friction damage between the filter and pump. To replace the O-ring, open the sprayer housing and twist the pump off. Carefully pry the old O-ring off and clean the mounting area to ensure a good seal for the new ring. Place the O-ring over the filter and apply light pressure until it is flat against the surface. Reassemble the equipment to complete your repair.
Pool and Spa Ps2 Filter Cs12
1 Review
In Stock
Part Number: WF2CB
$62.93
This is a carbon water and ice filter designed for various refrigerator makes and models. The filter dimensions are 6.75 inches in height, 2.25 inches in length, and 5.25 inches in width. It is a genuine OEM filter. The frequency of replacement depends on usage but is recommended every 6 months or 400 gallons, whichever comes first. This filter effectively removes impurities such as lead, chlorine, mercury, cysts, and particulates, enhancing the overall water taste. Replacing this filter is a simple process: press and release the old one, usually located on the front of the refrigerator, and install the new filter in its place. To ensure optimal performance, run the dispenser for 2-3 minutes and discard the dispensed water to flush the filter and remove any impurities before using it for consumption.