Pruner Repair
Pruners work hard to clear branches, which can affect their parts from time to time. If your pruner is not functioning properly, we will guide you through identifying the symptoms and the parts that should be replaced or adjusted. No matter how small or big the repair, we will help you get your pruner in working order.
Leaks gas
Reported 17% of the time
If one of the following parts is damaged or worn out it can cause your pruner to leak gas: the grommet, primer bulb, O-ring, fuel tank, and fuel lines. We can help you fix this in no time with our repair guide. Note: this is a general repair guide. Check the manual provided by your owner for more specific repair information related to your model.
Won't start
Reported 11% of the time
Check the fuel tank, spark plug, ignition module, or carburetor if your pruner is not starting. The repair and symptom guide will help you better identify the part needed to be replaced and how. This is a general guide for your repair; for more detailed information on your model, refer to the owner’s manual.
Leaks bar oil
Reported 9% of the time
Check the cap and fitting if bar oil is leaking from your pruner. Our repair and troubleshooting guide will help you fix this problem easily. Our repair information is a general guide to help you, but for more specific repair information related to your model, check your owner’s manual.
Chain falls off
Reported 7% of the time
If your pruner chain falls off, check the chain, retaining rings, chain, sprocket, and bar. Our troubleshooting and repair guide can help you fix this problem efficiently. Our repair information is a general guide to help you, but for more specific repair information related to your model, check your owner’s manual.
Cuts poorly or not at all
Reported 6% of the time
Our repair and symptom guide can help you fix your pruner if it does not cut properly. The shaft, bar, blades, and chain should be checked. Note: this is a general repair guide. Check the manual provided by your owner for more specific repair information related to your model.
Engine rotates but chain doesn't
Reported 6% of the time
If your pruner engine is rotating, but the chain does not, refer to our symptom guide to help you identify the right part to replace. It could be the sprocket, bar, gears, or shaft. If you need specific repair instructions related to your model, refer to the manual provided by the manufacturer.
Won't telescope or binds
Reported 6% of the time
If your pruner will not telescope, check the clamps, knob, or shaft for damage. Our troubleshooting and repair guide will help you fix this problem. Check the manual related to your model for more specific repair instructions. Our instructions are a general guide.
Can't keep chain tensioned
Reported 6% of the time
If the chain cannot be kept tensioned on your pruner, our repair guide can help you fix this. Check the chain, sprocket, bar, and cover for damage. Check the manual related to your model for more specific repair instructions. Our instructions are a general guide.
Leaks oil
Reported 5% of the time
If your pruner is leaking oil, the following parts might need to be replaced: the cover, gasket, cap, and seals. Follow our symptom and repair guide for more information on the right part to replace. If you need specific repair instructions related to your model, refer to the manual provided by the manufacturer.
Hard to start
Reported 5% of the time
Refer to our repair and symptom guide to find out what is causing your pruner to not start. The following parts should be checked for damage: the fuel lines, fuel filter, air filter, spark plug, fuel vent, and gasket. Check the manual related to your model for more specific repair instructions. Our instructions are a general guide.
Engine will idle but dies at full throttle
Reported 4% of the time
If your pruner idles, but stops at full throttle, check the following parts: the carburetor, fuel lines, gasket, and fuel filter. One or more of these parts might need to be replaced. To find the right one, follow our repair and symptom guide. This is a general guide for your repair; for more detailed information on your model, refer to the owner’s manual.
Bar oiler doesn't work
Reported 4% of the time
If the bar oiler in your pruner is not working, check the oil pump, gears, bar, and cap. Follow our troubleshooting guide to help you easily fix your problem and find the right part to replace. This is a general guide for your repair; for more detailed information on your model, refer to the owner’s manual.
