Chainsaw Engine Gasket Kit [530069608] for Power Tools

Description:

This is an authentic manufacturer-sourced replacement part which is specially designed for use with Poulan gas powered chainsaws. Gaskets are generally utilized to provide a tight seal between connected parts, over time the material may wear out and even begin to crack eventually requiring a replacement. This high-quality kit is sold individually, keep in mind it includes all the necessary components to fix a leaking carburetor. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of these components.

We do offer an article and video on How to Clean a 2 Cycle Engine Carburetor. Here is the link.
How to Clean a 2 Cycle Engine Carburetor

Compatibility

This part is compatible with the following machines:

Poulan

Expand the 150+ compatible machines

Products Compatibility

This item works with the following types of products:

• Chain Saw
• Saw

Repair Instructions: Submitted by Customers Like You

1 of 1 people found this instruction helpful

Tool Type:

Chain Saw

Parts Used:

Carburetor Adapter - 530049700

Chainsaw Engine Gasket Kit - 530069608

Repair Difficulty:

Easy

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Wrench Set

Cracked Carburetor Adapter.

I replaced Carburetor Adapter and Gaskets. It was very simple.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Chain Saw

Parts Used:

Chainsaw Engine Gasket Kit - 530069608

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Pliers

Fuel leakage from old gasket on cap

Replaced old gasket on the cap with new gasket

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Chain Saw

Parts Used:

Chainsaw Engine Gasket Kit - 530069608

Assembly-Seal & Bearing - 530056363

Sealant-Liquid - 100106

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Socket set, torx driver and socket, clutch removal tool, worm gear tool

Air/Vac Leak - would not throttle up.

Watched video from eReplacement Parts for engine seal replacement. This was an excellent video of step-by-step instructions. I did not like the liquid sealant I purchased. Go with a brand you know. Overall, the repair was fairly simple with the correct tools.
- clutch removal tool
-worm gear removal/installation tool
-coil spacer device (thick business card)
I would attempt this repair again with confidence.
Another hint, since you have to do a total dis-assemble of the engine you may consider replacing the piston ring while you have it apart. Also the oil pump to be safe.
This saw was purchased in 2006 and was 13 years old before it needed this type of repair.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Chain Saw

Parts Used:

Chainsaw Engine Gasket Kit - 530069608

Strap-Ground - 530047442

Piston Kit - 530071408

Repair Difficulty:

Medium

Time Spent Repairing:

1-2 hours

Tools Used:

, A variety of different common hand tools

Piston worn out

Disassemble complete engine and replace piston piston ring and piston pin . I wish our cylinder was still available but had to make do with the old one have about four hours and saw cutting time now still runs good

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Chain Saw

Parts Used:

Chainsaw Engine Gasket Kit - 530069608

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers, Socket set, Wrench Set

Would not idle

1 Replaced carb, intake gaskets, and crankcase o-ring.
2 Adjusted lo speed fuel mixture and idle speed screw.
3 Apparently fixed an air leak and now idles properly

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Chain Saw

Parts Used:

Fuel Line - 530069247

Foam Air Filter - 530037793

Chainsaw Engine Gasket Kit - 530069608

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Pliers

Fuel line broken

Remove top access cover to spark plug, remove side cover with pull cord, remove fuel cap, get fuel filter out from tank, clean out tank, remove carb. clean carb, push in new fuel line and purge line, attach fuel filter, attach purge line plug, install lines to primer bulb. install new gasket, then lines to carb. put mix gas, primed, full choke, switch on pull three times, move choke to 1/2 pull again and it started. very easy to do.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Chain Saw

Parts Used:

Chainsaw Engine Gasket Kit - 530069608

Ring- Piston - 530029805

Repair Difficulty:

Medium

Time Spent Repairing:

1-2 hours

Tools Used:

Screwdriver, Socket set, Nutdriver, Cylinder Buffer and Ring Compressor

Bought it used, had been run without proper fuel oil mix. Would not start.

Full engine disassembly and reconditioning. Cleaned engine and all parts, cleaned cylinder and replaced ring to get better compression, cleaned and adjusted plug, replaced fuel line with new, and adjusted carburetor. Replaced and adjusted starter rope, and changed engine/carburetor gaskets where needed from set assortment.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

0 of 1 people found this instruction helpful

Tool Type:

Chain Saw

Parts Used:

Chainsaw Engine Gasket Kit - 530069608

Repair Difficulty:

Easy

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers, Wrench Set

will not run

installed gaskets works like new

Did you find this story helpful?

Thanks for voting and helping fellow customers!

0 of 1 people found this instruction helpful

Tool Type:

Chain Saw

Parts Used:

Chainsaw Engine Gasket Kit - 530069608

Piston Kit - 530071408

Repair Difficulty:

Medium

Time Spent Repairing:

1-2 hours

Tools Used:

Screwdriver, Pliers, Socket set, Wrench Set, Torx

Engine lost compression, Piston and ring scored.

Disassembled the chainsaw, removed the old components and put in the new parts.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Reviews

Average Rating (out of 5):

5 Reviews

Click to filter by ratings:

5 stars

5

4 stars

0

3 stars

0

2 stars

0

1 stars

0

Sort by:

Highest Rating
Most Recent

< PREV

1

NEXT >

Always what I ordered and always what I need THANKS

Chainsaw is working great THANKS

ROSEMARY - November 12, 2020 Verified Purchase

Great fit. Quality parts

Perfect fit. Fast shipping

Guest - November 16, 2019 Verified Purchase

parts arrived timely, correct for my type

followed repair video

Guest - October 22, 2019 Verified Purchase

Exactly as ordered

Bought the gasket set for my Poulan chainsaw in August 2019. Gaskets look great and appear to be more than what I needed in the set. Price was great as well. No brainer, I was working around the carb, tore an old gasket and since I was overhauling the chainsaw anyway, just ordered the whole set of gaskets. Shipped as promised tho UPS' status disagreed with erepalcementparts.com's status on where the order was. An email was quickly answered with no fuss. I have no hesitation about ordering replacement parts from them again and they've even earned a bookmark in my browser. Thanks for a perfect customer experience all around.

Guest - September 19, 2019 Verified Purchase

easy repaire parts worked great

Parts arrived in great condition.

william - August 26, 2019 Verified Purchase

Verified Purchase

eReplacementParts Team

Sort by:

Highest Rating
Most Recent

< PREV

1

NEXT >