Foam Air Filter

Fuel Cap Assembly - 580940901

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Pliers

Replaced Fuel lines

Replaced fuel line and other items on chain saws and the parts cost less from here then buying then local. Also looked at youtube. But I will get all my parts from this web site because I like their prices and delivery time.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Chain Saw

Parts Used:

Spark Plug - 952030150

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Socket set

Filter was shot and spark plug need replacing.

Removed the cover, replaced the spark plug and the air filter.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Chain Saw

Parts Used:

Fuel Line Fitting - 530023877

Carburetor Repair Kit Walbro (WT324) - 530069826

Fuel Filter - 530095646

Repair Difficulty:

Medium

Time Spent Repairing:

1-2 hours

Tools Used:

Screwdriver, Pliers, Socket set, Nutdriver, Forceps, scissors

Fuel lines deteriorated, carburetor dirty, filter dirty, chain worn out

1. Removed, cleaned and rebuilt carburetor.
2. Replaced fuel, purge lines and fuel filter.
3. Oiled and replaced air filter.
4. Removed and checked piston and rings.
5. Replaced spark plug.
6. Replaced chain.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Chain Saw

Parts Used:

Fuel Filter - 530095646

Repair Difficulty:

Medium

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Pliers, Nutdriver, Needle nose pliers

Fuel, purge lines and air filter rotted away.

Removed engine cover to expose carb and old fuel/purge lines. Remove old lines from carb and primer bulb. Cut new fuel line/purge line ends at an angle to allow them to be started through access holes into the fuel tank. Pull them through with needle nose pliers from inside the tank. Attach fuel filter to fuel line(inside tank) and attach other end of fuel line to carb. Connect purge line to primer bulb. Add a small length of fuel line from primer bulb to secondary carb fitting to prime engine. Check for fuel leaks then reattach engine cover.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Chain Saw

Parts Used:

Fuel Filter - 530095646

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers, Nutdriver

Primer bulb was cracked,air filter dry rotted,and fuel lines brittle

1. Opened access
2. Removed bad components
3.Installed new fuel lines and connected to carb.
4.installed new primer bulb and connected fuel line
5. Installed new air filter
6. Added gas and started saw.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Chain Saw

Parts Used:

Bar Adjustment Kit - 530069611

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers, Socket set, Long hemostats

Gas lines deteriorated

Removed chain cover and starter cover removed air filter removed carburetor nuts pulled off carburetor while squeezing gas trigger so linkage will remove from carburetor . cut gas lines 1 in long in half to insert into tank pulled through with hemostats attach lines to carburetor an reassemble this was the hardest part getting gas lines through holes in Gas tank

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Chain Saw

Parts Used:

Fuel Cap Assembly - 580940901

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver

Old and wore out

Remove top and side cover remove old parts install new,

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Chain Saw

Parts Used:

Spark Plug - 952030150

Repair Difficulty:

Medium

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Socket set, Nutdriver, Adjustable Wrench

Chainsaw would not start

1. Removed the outer covers
2. Cleaned all of the removed parts
3. Removed the carb, disassembled it and cleaned it.
4. Replaced damaged fuel line
5. Reassembled the carb and installed it
6. Checked the gap and replaced spark plug
7. Replaced air filter and reassembled the outer casings
8. Chainsaw started right up.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Chain Saw

Parts Used:

Fuel Cap Assembly - 580940901

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Screwdriver

Primer bulb leaked.

Unscrewed the old bulb and inserted the new one. Only needed a screwdriver.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Chain Saw

Parts Used: