Watch The
Repair Video

Assembly-Seal & Bearing

Part Number: 530056363

Order within the next 6 hours

and your part ships today!

Questions & Answers

Repair Instructions

*This part replaces obsolete part #: 530019259 and 530047827.

Product Information

Manufacturer: Poulan, Husqvarna, Jonsered

Product Number: 530056363

Classification: Part

Weight: 0.08 lbs.

Shipping: Ships Worldwide

Description:

This is an authentic part assembled by original manufacturer. It fits various models of Poulan chainsaws. Ball bearings lessen friction between moving parts. They also hold and stabilize parts\' position and angle. Bearings are high wear pieces and can need replacement often. Included is one (1) bearing and one (1) seal.

Warning: California's Proposition 65

Compatibility

This part is compatible with the following machines:

Poulan

Expand the 150+ compatible machines

Products Compatibility

This item works with the following types of products:

• Chain Saw
• Saw

Questions & Answers

Sort by

What is the correct part number for the assembly-seal and bearing for my model?

Obed for model number 2250 LE asked on 2019-10-27

Hi Obed, the correct part is 530056363 for model 2250 LE. Thank you for your question and good luck with your repair!

Did this question help you?

Repair Instructions: Submitted by Customers Like You

1 of 1 people found this instruction helpful

Tool Type:

Chain Saw

Parts Used:

Assembly-Seal & Bearing - 530056363

Cylinder Gasket Kit - 530071894

Repair Difficulty:

Medium

Time Spent Repairing:

More than 2 hours

Tools Used:

Screwdriver, Pliers, Socket set, Impact wrench

Poulan P3314 would not start

1. Purchased two carburetors that did not work. 2. Had a weak spark so I replaced the ignition coil. 3. Took engine out and replaced the main bearings. 4. Replaced the fuel lines and filter. 5. Purchased a new Zama carb from eReplacementParts.com and installed it. 6. Turned the Lo and High carb adjustment screws out 1 and 1/2 turns. 7. Replaced the primer bulb. 8. Put fresh 40:1 gasoline in. The saw finally started up and ran. 8. Ran the saw about a medium RPM and turned the Lo carb adjustment screw slowly clockwise until maximum RPM and the saw then idled nice without shutting off. The parts from eReplacement.com were excellent quality. I should have purchased a new carb from eReplacementParts.com to start with. I did purchase a flywheel removal tool and with an impact wrench removed the flywheel. I watched a eReplacementParts You Tube video on replacing the engine main bearings. The video was VERY helpful.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Chain Saw

Parts Used:

Assembly-Seal & Bearing - 530056363

Retainer-Piston Pin - 530015697

Carburetor Gasket - 530019172

Oiler Gear 36/41 - 530029833

Crankshaft Assy 36/41 - 503920801

Impulse Pipe - 530053435

Repair Difficulty:

Medium

Time Spent Repairing:

More than 2 hours

Tools Used:

Screwdriver, Pliers, Socket set, Wrench Set, Nutdriver, homemade spanner wrench

engine seized

Tear the whole saw apart, cleaned and inspected parts, make a parts list of parts needed, check availability and pricing, order parts, found the need for another part also, ordered again.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Chain Saw

Parts Used:

Chainsaw Engine Gasket Kit - 530069608

Assembly-Seal & Bearing - 530056363

Sealant-Liquid - 100106

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Socket set, torx driver and socket, clutch removal tool, worm gear tool

Air/Vac Leak - would not throttle up.

Watched video from eReplacement Parts for engine seal replacement. This was an excellent video of step-by-step instructions. I did not like the liquid sealant I purchased. Go with a brand you know. Overall, the repair was fairly simple with the correct tools.
- clutch removal tool
-worm gear removal/installation tool
-coil spacer device (thick business card)
I would attempt this repair again with confidence.
Another hint, since you have to do a total dis-assemble of the engine you may consider replacing the piston ring while you have it apart. Also the oil pump to be safe.
This saw was purchased in 2006 and was 13 years old before it needed this type of repair.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Product Information

Manufacturer: Poulan, Husqvarna, Jonsered

Product Number: 530056363

Classification: Part

Weight: 0.08 lbs.

Shipping: Ships Worldwide