eReplacementParts.com
877-346-4814
Poulan Parts
Preferred Partners of
Repair Parts Home  Power Tool Parts  Poulan Parts  530071894 Cylinder Gasket Kit
photo thumbnailphoto thumbnail360 degree photo thumbnail

Cylinder Gasket Kit

Part Number: 530071894
PoulanJonseredHusqvarnaWeed Eater
Availability: 16 in stock
Price: $11.46
Ships within 1 business day
Product Information
Manufacturer: Poulan, Jonsered, Husqvarna, Weed Eater
Product Number: 530071894
Classification: Part
Weight: 0.01 lbs.
Shipping: Ships Worldwide
Description:
This kit is used for various Poulan and Husqvarna models of chainsaws. It is a genuine replacement part produced by original manufacturer. This seven (7) piece kit includes all gaskets and O-rings used in the engine. One (1) kit per order.
Frequently Purchased With
Compatibility

This part is compatible with the following machines:

Poulan
Jonsered
Husqvarna
Expand the 150+ compatible machines
Products Compatibility

This item works with the following types of products:

  • • Chain Saw
  • • Saw
Questions & Answers

No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
5 of 6 people found this instruction helpful
Tool Type:
Chain Saw
Parts Used:
Fuel Line - 530069247
Purge Line - 530069216
Fuel Line Fitting - 530023877
Purge Bulb - 530047721
Cylinder Gasket Kit - 530071894
Repair Difficulty:
Easy
Time Spent Repairing:
More than 2 hours
Tools Used:
Screwdriver, Pliers, Socket set, Hemostat for main gas line
Wouldn't keep a prime, bad purge bulb old broken gas lines.
Removed shroud over carb. Removed pull starter shroud. Removed throttle linkage from carb and from saws handle that way you can take the air filter housiing off and get it out of the way, simple to put back together. Removed the choke and kill switch then removed the carb and the carb manifold in order to replace the main gas line to the tank. This makes things alot easier when replacing the main gas line. Installing the main line was the hardest because the line fits extemely tight into the gas tank. I cut the end of the gas line at an angle in order to get it started in to the tank. The gas line I bought comes with instructions to help you do it right. Once I got it started into the tank I used a surgical Hemostat to reach in the tank and pull the hose into the tank to where I could cut the end square and put a new coupler on it and then attach the fuel filter. Long nose needle nose pliers would work but I didn't have a pair. Pulling the hose into the tank was the hardest part because the gas line fits really tight. I put a little WD40 on the line to help lubricate it so it would pull thru easier. Then I replaced all the other gas lines, installed a new Purge Bulb, put new gaskets on the manifold (I didn't replace any internal carb gaskets) I put everything back together, put gas in the tank, primed the Purge Bulb and after two pulls it fired right up and runs good.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Chain Saw
Parts Used:
Piston Ring - 545160401
Cylinder Gasket Kit - 530071894
Clutch Removal Tool - 530031116
Repair Difficulty:
Medium
Time Spent Repairing:
More than 2 hours
Tools Used:
Screwdriver, Pliers, Socket set
Wouldn't cycle. Something caught in engine.
E parts made the repair not only possible but with the video it was easy to follow. He parts not only supplied the how-to video but one easy click provided all the parts necessary. Truly a five-star experience!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Chain Saw
Parts Used:
Cylinder Gasket Kit - 530071894
Crankcase Casting - 530057941
Spark Plug - 503235111
Repair Difficulty:
Medium
Time Spent Repairing:
More than 2 hours
Tools Used:
Screwdriver, Socket set, Wrench Set, Nutdriver, Clutch removal tool, and Fly wheel holder
Cylinder piston and carburetor replacement
1) Remove the filter housing
2) Remove the top body cover
3) Remove carburetor and intake body
4) Remove Pull Rope housing
5) Remove chain clutch and flywheel
6) Remove oiler housing and oiler gear
7) Remove bottom 4 screw that holds the cylinder assembly in plastic housing.
8) First Remove saw and saw bar
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Chain Saw
Parts Used:
Cylinder Gasket Kit - 530071894
Kit-Cylinder - 530071884
Kit-Piston - 530071883
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
, T-25 T-27 10mm socket cordless reversible drill
Scored piston and cylinder
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Chain Saw
Parts Used:
Bar Wrench - 530031163
Cylinder Gasket Kit - 530071894
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, Pliers, Socket set, Wrench Set, (wrench set is torx t20 and t25)
hard to pull
1. Disassembled entire saw.
2. Cleaned off carbon from top of piston and cylinder head.
3. Replaced fuel line with filter.
4. Reassembled saw.
5. Added new fuel and it fired right up without to much resistance on the rope.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Chain Saw
Parts Used:
Assembly-Seal & Bearing - 530056363
Cylinder Gasket Kit - 530071894
Repair Difficulty:
Medium
Time Spent Repairing:
More than 2 hours
Tools Used:
Screwdriver, Pliers, Socket set, Impact wrench
Poulan P3314 would not start
1. Purchased two carburetors that did not work. 2. Had a weak spark so I replaced the ignition coil. 3. Took engine out and replaced the main bearings. 4. Replaced the fuel lines and filter. 5. Purchased a new Zama carb from eReplacementParts.com and installed it. 6. Turned the Lo and High carb adjustment screws out 1 and 1/2 turns. 7. Replaced the primer bulb. 8. Put fresh 40:1 gasoline in. The saw finally started up and ran. 8. Ran the saw about a medium RPM and turned the Lo carb adjustment screw slowly clockwise until maximum RPM and the saw then idled nice without shutting off. The parts from eReplacement.com were excellent quality. I should have purchased a new carb from eReplacementParts.com to start with. I did purchase a flywheel removal tool and with an impact wrench removed the flywheel. I watched a eReplacementParts You Tube video on replacing the engine main bearings. The video was VERY helpful.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Chain Saw
Parts Used:
Zama Carburetor - 545070601
Cylinder Gasket Kit - 530071894
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, Pliers, Adjustable Wrench
Wouldn't run.
Changed out the carburetor.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Chain Saw
Parts Used:
Cylinder Gasket Kit - 530071894
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Pliers, Socket set
Muffler gasket blew out
Removed the spark arrester from the muffler to access the two bolts holding the muffler. Requires a long star driver bit to reach the bolts. Removed old gasket and replaced with new gasket. Re installed the muffler and spark arrester . Quite simple and easy. Had to purchase a gasket kit to get the muffler gasket. Hope I don't need the others later. But have them if needed.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
0 of 1 people found this instruction helpful
Tool Type:
Chain Saw
Parts Used:
Cylinder Gasket Kit - 530071894
Kit-Cylinder - 530071884
Kit-Piston - 530071883
Cover-Air Filter - 530059001
Repair Difficulty:
Easy
Time Spent Repairing:
More than 2 hours
Tools Used:
Screwdriver, Pliers, Socket set, Wrench Set, Adjustable Wrench
Cylinder was badly scored. No compression.
Disassemble engine. Cleaned crank and rod plus all bearings. Lightly lubed. Installed ring on piston. Put piston on rod with new wrist pin an clips an slid assembly in to cylinder an bolted it back in the housing. Finished assembling. Tuned carburetor, works great.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
4.8
Average Rating (out of 5):
5 Reviews
Click to filter by ratings:
5 stars
4
4 stars
1
3 stars
0
2 stars
0
1 stars
0
  • Highest Rating
  • Most Recent
< PREV
  • 1
NEXT >
  • Poulan Repair Kit - Perfect Replacement
    This kit was a perfect replacement. My chainsaw is working again. This site is a wonderful source for replacement parts for all manner of devices!
    Raymond - December 3, 2020 Verified Purchase
    Easy Shopping-Quick Service
    I've been repairing a Poulan PP4218AVX chainsaw. This gasket set is only one from a long list of parts that I've ordered from eReplacementParts. They seem to have become my go-to place to order parts for this rebuild. They have the parts and they are quickly shipped. Everything has fit perfectly. I will continue to shop here for my tool repair needs.
    Guest - November 9, 2020 Verified Purchase
    Great fitting parts
    All parts neatly package not twisted good quality
    Guest - July 18, 2020 Verified Purchase
    Good price good part
    Arrived on time. Good information on website
    Guest - December 14, 2019 Verified Purchase
    Easy repair, just what I needed
    Part was in great shape, all pieces there
    Guest - October 16, 2019 Verified Purchase
    Verified Purchase
    eReplacementParts Team
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    NEXT >
    Product Information
    Manufacturer: Poulan, Jonsered, Husqvarna, Weed Eater
    Product Number: 530071894
    Classification: Part
    Weight: 0.01 lbs.
    Shipping: Ships Worldwide
    Repair Guides
    Watch the Repair Video for Cylinder Gasket Kit
    Articles:
    Overhaul overdue? Step-by-step instructions show you how to install the cylinder gasket and O-ring kit on your Poulan ch...
    January 04, 2017

    Fixing things makes sense...

    ...And we make it easy! With our Fix app, you always have a personalized repair guide on-hand. Easily find manuals and replacement parts on your phone while you’re DIYing in the garage or garden.

    "Love the flexibility of the app to add everything in the home and garage. Access to manuals and parts right there makes it convenient."

    Available on the App Store Get it on Google Play
    eReplacementParts.com
    7036 South High Tech Dr.
    Midvale, UT 84047
    visa mastercard discover american express PayPal