Compatibility
Products Compatibility
This item works with the following types of products:
- • Sander
Questions & Answers
will it fit my sander?
Douglas
for model number R2500
Hello, Thank you for the question. The Sander Pad for this model number is Part Number: 591636001. The 200202538 is not listed for the R2500. Hope this helps!
Will this fit a tool shop sander
Barbara Hamilton
Hello Barbara, thank you for writing. We would be happy to look into this, but we will need the model number for your unit to do so. We look forward to hearing back from you.
Is this the correct cushion assembly for our Ryobi S652D 1/4 sheet sander?
Noel
for model number Ryobi S652D
Hello Noel, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is Part Number: 039066005051. Thank you for your inquiry, good luck with this repair!
Repair Instructions: Submitted by Customers Like You
11 of 11 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Worn out pad
Unscrew (allen head screws) remove worn pad. Set new pad, screw in new pad......DONE
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Sander sheet pad plate was worn on front edge so it was no longer flat
1. Removed four screws from old plate.
2. Removed pad, replaced it with new pad.
3. Replaced screws
2. Removed pad, replaced it with new pad.
3. Replaced screws
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Torx wrench
Replaced cushion sanding pad
Took 4 screws out of the old pad and installed the new pad with same screws. It was a snap.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
, Screwdriver with star bits
Sand paper kept coming off.
1. Removed scews that secured part to be replace.
2. Removed the defective part paying attention to position and fit.
3. Placed new part in proper position and secured with original screws.
pretty much a piece of cake.
2. Removed the defective part paying attention to position and fit.
3. Placed new part in proper position and secured with original screws.
pretty much a piece of cake.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Torx head screwdriver
Worn out backing plate
1 Removed old backing plate
2 Installed new backing plate
2 Installed new backing plate
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Sander pad needed replacing
Unscrewed 4 screws, remove pad and plate, put new one on, screw 4 screws back in and done.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Pad worn out due to abuse by owner
Screws taken out, worn out pad removed and new one installed
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Sandpaper was slipping and not held securely.
1. Removed four screws securing sander backing plate.
2. Removed spring clamp assembly
3. Removed rubber cushion.
4. Cleaned surface area for new rubber cushion.
5. Peeled backing paper off new rubber cushion and adhered to correct location.
6. Positioned new spring clamp assembly in proper location.
7. Placed new sander backing plate assembly in proper location and secured with original screws.
2. Removed spring clamp assembly
3. Removed rubber cushion.
4. Cleaned surface area for new rubber cushion.
5. Peeled backing paper off new rubber cushion and adhered to correct location.
6. Positioned new spring clamp assembly in proper location.
7. Placed new sander backing plate assembly in proper location and secured with original screws.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
, T20 star
Sandpaper kept breaking loose
Remove four screws to remove plate and padding.
Replace plate and padding with screws
Replace plate and padding with screws
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Sand paper clip broke
1. Removed four screws to remove assembly
2. Reinstall assembly
2. Reinstall assembly
Did you find this story helpful?
Thanks for voting and helping fellow customers!
show more
Reviews
3 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
2
4 stars
1
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
Part was a perfect match
Equipment diagram was easy to read. It made identifying the appropriate part simple. Narrative about part replacement procedure was spot on.
Guest -
13 days ago
Verified Purchase
Fits Perfect
These replacement pads fit directly to the Ridgid sander. Nice to have a spare.
Guest -
May 14, 2019
Verified Purchase
Quality part
No effort whatsoever to install and the part feels more reliable than the factory part. No problems so far.
Robert -
5 days ago
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
