Easy
30-60 minutes
This item is a genuine OEM sourced replacement part that is intended to be used with forced air heaters from Pro Temp, Heat-Stream, Heat Hog, and Master. The plastic fuel filter connects to the fuel line and is used to prevent contaminants from entering the motor assembly. This item is available as an individual replacement part.
Fuel Filter Assembly 70-003-0100
OEM part for: Pro Temp, Heat Stream, Heat Hog, Master
Part Number: 70-003-0100
$13.70
In Stock
Ships within 1 business day 
Jump To:
Frequently Purchased Together ?
Compatibility
This Fuel Filter Assembly will fit the following 8 machines. Confirm this part works with your model, and view the detailed model diagrams and repair help we have to offer.
Pro Temp
Heat Stream
Heat Hog
Master
Show More Compatible ModelsThis item works with the following types of products:
- Heater Parts
Repair Videos ?
Watch the Repair Video for
Fuel Filter Assembly
Articles:
|
Step-by-step instructions for removing and installing the fuel filter on your ProTemp heater....
January 24, 2018
|
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Fuel Filter Assembly
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Air line was cracked so the heater would not light.
Donald - December 10, 2023
Tool Type
Heater
Difficulty
Easy
Time
30-60 minutes
Tools Used
Screwdriver, Pliers, Nutdriver, None
1. Removed the top of the heater.
2. Pulled the cover off the air pump at the back of the motor and installed the new filters.
3. Pulled the motor assembly up and back to replace the air hose. Does not need to be moved far but gives you access to route the new air line. Disconnected the air line and installed the new one.
4 removed the fuel line and filter. Installed new filter and fuel line.
5 Put back together and turned it on. It lit right up and ran fine. Also adjusted the pressure on the air pump at that time. My heater is nice there is a gage right on the air pump and pressure can be adjusted with the unit assembled.
Done and ready to have heat in the shop when it gets cold, which in central PA in December will be very soon.
2. Pulled the cover off the air pump at the back of the motor and installed the new filters.
3. Pulled the motor assembly up and back to replace the air hose. Does not need to be moved far but gives you access to route the new air line. Disconnected the air line and installed the new one.
4 removed the fuel line and filter. Installed new filter and fuel line.
5 Put back together and turned it on. It lit right up and ran fine. Also adjusted the pressure on the air pump at that time. My heater is nice there is a gage right on the air pump and pressure can be adjusted with the unit assembled.
Done and ready to have heat in the shop when it gets cold, which in central PA in December will be very soon.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Kerosene heater will turn on then stop.
Jon - October 25, 2023
Tool Type
Heater
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Pliers
Cleaned air filter and housings had some suet build up. Fuel filter damaged so I replaced it along with the fuel line because they were brittle. I also replace the rotor which had been damaged. Works great now.....
Did you find this story helpful?
Thanks for voting and helping fellow customers!
The fuel straw rotted off.
Christopher - September 9, 2023
Tool Type
Heater
Difficulty
Easy
Time
More than 2 hours
Tools Used
Screwdriver, Pliers, Power Drill, Socket set, Knife
Parts Used
Got the parts 2 months after I ordered and paid for them. Have not done the repair yet. Thanks for getting them to me... eventually.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Heater comes on but does not seem to be blowing as hot as it used to. After a minute or so it turns off and the green power light blinks
Ronald - February 7, 2020
Tool Type
Heater
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Pliers
Removed the side panel. Disconnected the fuel line and turned the filter counterclockwise to unlock the removed. Reinstalled in reverse.
Also replaced the thermostat sensor as directed by errplacements.
None of these corrected the problem.
I also replaced the roto kit.
Also replaced the thermostat sensor as directed by errplacements.
None of these corrected the problem.
I also replaced the roto kit.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Sharon - December 16, 2018
Tool Type
Heater
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Pliers, None
Parts Used
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Not running properly, low pressure, cracked air line and deteriorated fuel line
Matthew - December 1, 2018
Tool Type
Heater
Difficulty
Medium
Time
1-2 hours
Tools Used
Screwdriver, Pliers
Disassembly of the unit is pretty straightforward. Just seven sheet metal screws if I remember correctly. The only problem I encountered was that the nipple on the new fuel filter was the larger diameter than the old filter. The new fuel line purchased also has a much larger diameter to accommodate this. Unfortunately the unit was getting too much fuel after I completed the repair. It was not running properly. I went to the local hardware store and purchase the smaller diameter new fuel line and was able to stretch this over the larger nipple of the new filter. It runs perfectly again.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Missing filter.
anthony - January 15, 2018
Tool Type
Heater
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Parts Used
Replaced the old with the new.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Old filter.
Kyle - February 6, 2017
Tool Type
Heater
Difficulty
Easy
Time
More than 2 hours
Tools Used
Parts Used
Replaced an old filter with a new one. Perfect fit!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
