Watch The
Repair Video

Diaphragm and Gasket Kit

Part Number: P005002290

2 Reviews

Order within the next 5 hours

and your part ships today!

Questions & Answers

Repair Instructions

*This part replaces obsolete part #: P005001660.

Product Information

Description:

This is a Genuine OEM rebuild kit used on a variety of Lawn and Garden Equipment. This kit contains the necessary Gaskets, Diaphragms, Needle and Spring needed to rebuild your carburetor. If your engine runs sluggish or it dies shortly after starting it, you may need to rebuild your carburetor.

Replacing these items you would need a Screwdriver and Pliers.

Warning: California's Proposition 65

Compatibility

This part is compatible with the following machines:

Shindaiwa

DH212 (S78311001001 - S78311999999) Hedge Trimmer

Echo

Expand the 150+ compatible machines

Questions & Answers

Sort by

No questions have been asked yet

Repair Instructions: Submitted by Customers Like You

6 of 6 people found this instruction helpful

Tool Type:

Trimmer

Parts Used:

Fuel Grommet - 13211546730

Fuel Filter - A369000480

Fuel Tank Vent - A356000031

Fuel Line - V471001211

Diaphragm and Gasket Kit - P005002290

Air Filter - A226001410

Repair Difficulty:

Medium

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Pliers, Socket set

Would not start easy and would not stay running.

Removed carburetor cleaned , disassembled , replaced parts, and reassembled. will start and run after reassembly.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

4 of 4 people found this instruction helpful

Tool Type:

Hedge Trimmer

Parts Used:

Diaphragm and Gasket Kit - P005002290

Repair Difficulty:

Easy

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, compressed air

Hard starting

Repair took 30- 60 minutes over two days. I removed all old parts and sprayed carb block with carb cleaner and used compressed air to blow out. I then soaked carb block in carb cleaner over night and then repeated blow out of all holes 2 more times. Being EXTREMELY careful not to allow any dirt into carb as I reassembled and it would not start. Check assembly and slightly adjusted needle and reassembled. Starts and runs perfect again. Soaking over night help to remove all deposits left behind by California mix gas.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

2 of 2 people found this instruction helpful

Tool Type:

Edger

Parts Used:

Diaphragm and Gasket Kit - P005002290

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Pliers, Adjustable Wrench

Edger would not start due to no fuel getting to piston cylinder.

1. Removed, disassembled, cleaned and inspected the carburetor parts.
2. Found a tiny hole in the fuel diaphragm by shining light on opposite side.
3. Ordered and received a gasket and diaphragm kit from E Replacement Parts.
4. Installed kit and replaces the fuel suction line and a primer bulb.
5. Started engine and adjusted fuel jets.
6. Runs Well!

Did you find this story helpful?

Thanks for voting and helping fellow customers!

2 of 2 people found this instruction helpful

Tool Type:

Edger

Parts Used:

Purge Bulb - P005003120

Diaphragm and Gasket Kit - P005002290

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Power Drill, Bench

Primer cracked from age . Had not been used for a couple of years

Removed 4 screws to take off primer bulb. Removed air filter cover and took out the 2 carb mounting screws. Did not disconnect throttle cable. Replaced mounting gasket and lower diaphragm. Inside of carb looked good so i just mounted it back with new gasket. Pretty easy and quick. It was an echo 2 cycle edger weed whacker. Took me less than 30 minutes. Started right up. Before this it was leaking and would not start. Kept flooding the plug.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Trimmer

Parts Used:

Spark Arrester Screen - 14586240630

Diaphragm and Gasket Kit - P005002290

Repair Difficulty:

Medium

Time Spent Repairing:

1-2 hours

Tools Used: