Watch The
Repair Video

Belt - Drive

Part Number: 55-9300

1 Reviews

Order within the next 14 hours

and your part ships today!

Questions & Answers

Repair Instructions

Product Information

Manufacturer: Toro

Product Number: 55-9300

Classification: Part

Weight: 0.15 lbs.

Shipping: Ships Worldwide

Description:

The drive belt connects to the engine pulley. This part is an OEM from Toro for use in snowthrowers and is sold individually. It will need replacing if it becomes broken or stretched. During replacement, a socket set and a nutdriver might be required.

Warning: California's Proposition 65

Frequently Purchased With

Scraper
$31.71

Compatibility

This part is compatible with the following machines:

Toro

Expand the 66 compatible machines

Products Compatibility

This item works with the following types of products:

• Snowblower

Questions & Answers

Sort by

No questions have been asked yet

Repair Instructions: Submitted by Customers Like You

1 of 1 people found this instruction helpful

Tool Type:

Snowblower

Parts Used:

Belt - Drive - 55-9300

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Socket set, Nutdriver

Drive belt fit perfectly

Followed YouTube video. Only problem encountered was a rounded bolt head, which was easily removed. https://www.youtube.com/watch?v=jctkVV-wf_M

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Fuel Filter - 56-6360

Clamp - 2412-98

Rotor Blade - 99-9313

Scraper - 55-8760

Belt - Drive - 55-9300

Gas Line - 49-2481

Spark Plug - 50-1170

Repair Difficulty:

Medium

Time Spent Repairing:

More than 2 hours

Tools Used:

Screwdriver, Pliers, Power Drill, Socket set, Wrench Set

Rotor blade, tune up

Changing rotor blade was difficult because of tight space to work in. Reassembling plastic covering and control panel was the most difficult. Had to loosen all bolts on front and rear covering to aline and reassemble. Drive belt, spark plug, gas lines and filter were the easiest. One bolt on drive belt side cover was worn down so much could not use wench, had to drill out and replace.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Boot-Switch - 61-4810

Belt - Drive - 55-9300

Spark Plug - 50-1170

Repair Difficulty:

Medium

Time Spent Repairing:

1-2 hours

Tools Used:

Screwdriver, Socket set, Wrench Set

Nothing at all.

I had to remove part of the shroud covering the starter switch and dissemble the switch in order to install the switch boot. I also had to remove a side cover to gain access to the belt. Replacing the spark plug was a simple task whereas it was staring me in the face after removing part of the engine shroud. The parts I purchased were a perfect fit. I will certainly order from eReplacements Parts again when needed.
Ken from Acushnet MA

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Screw-Carr - 3229-11

Rotor Blade - 99-9313

Nut-Keps - 32149-2

Scraper - 55-8760

Belt - Drive - 55-9300

Repair Difficulty:

Hard

Time Spent Repairing:

1-2 hours

Tools Used:

Screwdriver, Pliers, Socket set, Wrench Set, Nutdriver, Vise-Grips,Sheet metal bending pliers, Hammers & anvils

Snow Thrower: worn drive belt, worn and broken scraper blade, worn rubber impeller blades

1. Removed side panel cover over drive train
2. Removed and replaced Drive belt.
3. Removed Scraper Blade bracket
4. Removed old Scraper Blade
5. Straightened bottom panel on which scraper blade mounts (badly bent)
6. Installed new Scraper Blade
7. Removed and replaced Rubber Impeller Blades (This is the worst part. There is no access to side nuts without removing the impeller shaft, drive pulley, bearings,belt, etc. Use small needle-nose vise-grips to hold the nuts in place, AND hold the rubber blade to the impeller shaft frame while driving the Torx bolts with a power nut driver, and a Flex-extension on the driver).
8. Replaced Side panel.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Reviews

Average Rating (out of 5):

1 Reviews

Click to filter by ratings:

5 stars

4 stars

3 stars

2 stars

1 stars

Sort by:

Highest Rating
Most Recent

< PREV

NEXT >

Great part

The belt arrived quickly and was the correct size- easy to order. Thank-you will use your web site again.

Guest - December 15, 2020 Verified Purchase

Verified Purchase

eReplacementParts Team

Sort by:

Highest Rating
Most Recent

< PREV

NEXT >

Product Information

Manufacturer: Toro

Product Number: 55-9300

Classification: Part

Weight: 0.15 lbs.

Shipping: Ships Worldwide