eReplacementParts.com
877-346-4815
Hoover Parts
Repair Parts Home  Vacuum Parts  Hoover Parts  H-303202001 Brush Roll Assembly

Install
Videos!
Grid squares measure 1x1 inch

Brush Roll Assembly H-303202001

Part Number: H-303202001
Hoover
Availability: In Stock
Price: $17.68
Ships within 1 business day

*This part replaces obsolete part #: 303202001 and 303280001.

Product Information
Description:
This authentic manufacturer approved replacement brush roll assembly is designed for use with Hoover vacuums. The spinning motion of the brush rolls picks up the dust and dirt from the floor. Over time bristles will wear out and would need to be replaced. It is made out of plastic and it is sold individually.

When replacing this part you would need a screwdriver.

• Remove nozzle plate
• Remove old brush roller and snap the new one into place
• Secure the access plate
Frequently Purchased With
Products Compatibility

This item works with the following types of products:

  • • Vacuum

Questions & Answers for Brush Roll Assembly


Square end caps? Length? Will it do my model?
Guy for model number uh71107 asked on 2022-09-19
Hello Guy, Thank you for the question. Sadly, we do not have any information on the model number you provided. Could you please verify the number you provided us with? If it is correct, we recommend contacting the manufacturer and seeing if they could provide you with a part number, and then you are always welcome to check back to see if we carry the part. We hope this helps!
eReplacementParts Team September 19, 2022
Repair Instructions: Submitted by Customers Like You
Tool Type:
Vacuum
Parts Used:
Belt-stretch 2 Pack - H-AH20080
Brush Roll Assembly - H-303202001
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Original belt and spool were worn and slipping
Laid vacuum on back side.
Turned and slid 2 retainer clips and removed a few of the phillips screws to gain access to belt and spool ends.
I pushed belt off shaft, lifted out spool assembly.
Placed new belt on spool, engaged belt on motor shaft, then forced the two square ends of spool into their slots.
Replaced screws, slid and turned two retainer clips to lock assembly in.
Done.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Vacuum
Parts Used:
Exhaust Hepa Filter Assembly - H-303172001
Brush Roll Assembly - H-303202001
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
, hands
Brush Roller broke at the axle
Just needed to take the old one out and swap in the new one. Really simple.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Vacuum
Parts Used:
Brush Roll Assembly - H-303202001
Flat Non-stretch Belt - H-562289001
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
, bare hands only
was not picking up from carpet
Removed the old parts, replaced with new parts. So easy my wife did it,
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Vacuum
Parts Used:
Brush Roll Assembly - H-303202001
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
, no tools needed
Brush was worn down. Figured a new one would pick up better.
Read the instruction book that came with the vacuum from step 1 thru step 4. This was a very simple job.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
0 of 1 people found this instruction helpful
Tool Type:
Vacuum
Parts Used:
Brush Roll Assembly - H-303202001
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Bent brush roller
Removed the bottom of the vac.
Removed the old brush roll
Put the belt around the new brush roll and inserted it into the vacuum
Replaced the bottom
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
5
Average Rating (out of 5):
4 Reviews
Click to filter by ratings:
5 stars
4
4 stars
0
3 stars
0
2 stars
0
1 stars
0
  • Highest Rating
  • Most Recent
< PREV
  • 1
NEXT >
  • Replacement roller brush
    I had a hard time finding this part. I searched several on line sites to no avail. E replacement had it in stocks! Delivered fast and without issue. Part fits perfectly and I am vacuuming again! Thank you e replacement!
    Guest - June 21, 2023 Verified Purchase
    Saved a lot of money
    I saved a lot of money replacing the beater brush rather then buying a new vacuum. Found the part needed easily at a very reasonable price. Ordering was easy and it arrived when it said it would.
    Guest - April 12, 2021 Verified Purchase
    Easy repair
    Fast easy ordering-really fast delivery
    Guest - February 15, 2021 Verified Purchase
    replacement Part for vacuum
    Fit perfectly came quick. works great
    Guest - November 6, 2019 Verified Purchase
    Verified Purchase
    eReplacementParts Team
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    NEXT >
    Product Information
    eReplacementParts.com
    7174 South 400 West
    Suite 5
    Midvale, UT 84047
    visa mastercard discover american express PayPal