866-322-9842
Mon-Fri 7am-1am EST
Sat-Sun 7am-11pm EST
Repair Parts Home  Power Tool Parts  Porter Cable Parts  890725 Urethane Retainer

Urethane Retainer

Part Number: 890725
Porter Cable
Availability: 25+ in stock
Price: $2.30
Quantity:
Ships within 1 business day
Description:
This is a genuine Porter Cable replacement part, it is sold individually.
The purpose of the 890725 Retainer is to secure the pins used on the model numbers shown below.
It is advised to check the condition of the retainer often, for the reason the do deteriorate over time and can fall off of the pin they are retaining.
Product Information
Manufacturer: Porter Cable
Product Number: 890725
Classification: Part
Weight: 0.01 lbs.
Shipping: Ships Worldwide
Products Compatibility

This item works with the following types of products:

  • • Nailer
  • • Stapler
Questions & Answers

No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
32 of 34 people found this instruction helpful
Tool Type:
Nailer
Parts Used:
Gasket - 886114
Piston Stop - 886113
Urethane Retainer - 890725
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Wrench Set, Allen Wrenches, Needlenose Pliers, Air Tool Lubricant.
Pneumatic nailer intermittent fire, sticking.
In addition to a new piston bumper and manifold gasket I installed an O-ring kit. I started with the firing mechanism valve assembly which unscrews from the body using a box wrench. I cleaned the valve and fitted new O-rings the lubricated and reinstalled. When there was still a problem I disassembled further and found that the piston bumper had been dissolved after someone had tried to clean the tool with solvent. I removed the manifold cap, piston and cylinder and flushed the unit with WD-40. I wiped and dried all pieces then lubricated all O-rings and reassembled. The most important thing to remember is to properly reinstall the neoprene band that covers the small holes in the middle of the cylinder. The band acts as a one-way valve allowing the pressure charge to vent into the outer cylinder chamber where it then forces the piston back up completing the firing cycle. Everything else is step by step except for the band since it will slide out of position during disassembly and unless you know where it goes back your tool will fail to cycle. A little study and you can figure it out if you don't know.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
14 of 15 people found this instruction helpful
Tool Type:
Nailer
Parts Used:
Urethane Retainer - 890725
Retaining Ring - 897359
Piston Stop - 904685
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
, Allen keys
Urethane Piston stop crumbled
Super easy, E replacements online video walked me though it. The repair it showed was different than mine, but the disassembly steps showed me how to take apart the gun in order to diagnose the issue.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
5 of 6 people found this instruction helpful
Tool Type:
Nailer
Parts Used:
Urethane Retainer - 890725
Pin - 890724
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
, No tools needed
Pin and retainer came out of trigger
Pushed the pin thru the trigger and housing then pressed the retainer on the pin.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 3 people found this instruction helpful
Tool Type:
Nailer
Parts Used:
BRG Washer - 886115
Piston Stop - 886113
Urethane Retainer - 890725
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Pliers, Supplied allen wrench
Piston stop had deteriorated completely and firing piston would not retract.
1. Opened head of nailer with allen wrench.
2. Removed retaining washer complex.
3. Assembled new piston stop and bearing washer (per diagram).
4. Reattached head of nailer and secured with original bolts.
5. Secured trigger pin with urethane retainer.
6. Place oil in air intake and attached air supply to test nailer.
Worked like new.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 3 people found this instruction helpful
Tool Type:
Nailer
Parts Used:
Rubber Pad - 886188
BRG Washer - 886115
Piston Stop - 886113
Urethane Retainer - 890725
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Wrench Set
Porter Cable finish nailer was missing every other nail, and then every nail. Took it apart and piston bumper was falling apart.
Clean all the pieces out from the broken piston bumper, and clean muffler. Install new bumper, make sure when installing top portion of piston not to dislodge o-ring, I did and it leaked air when I put it back together, took back apart and saw it had pulled out, just take time and align piston when installing, goes in easy and properly. Put back together, and shooting like new. Hope this helps anyone.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Nailer
Parts Used:
Urethane Retainer - 890725
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Trigger fell out due to retainer clip being gone
Put the trigger assembly back in and installed the retainer
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Nailer
Parts Used:
Urethane Retainer - 890725
E-Ring - 883877
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Pliers
Missing O ring and retainer on trigger pin
Put trigger back together
Pushed E Ring on with pliers
Put retainer on by hand
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Nailer
Parts Used:
Piston Stop - 886113
Urethane Retainer - 890725
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
, Allen wrench
Roof Nailer losing air from the top,piston retainer shattered
Used parts diagram and instructions take apart tool piece by piece
Install new parts needed and assembled back together.
Used nailer and adjust air pressure until perfect .
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Nailer
Parts Used:
Urethane Retainer - 890725
Pin - 890724
Nose Cushion - 887249
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Pliers
Pin fell out and trigger fell off during operation. Urethane retainer on pin came off and was lost.
Lined up trigger with pin hole and inserted pin and retainer. eReplacementparts phone operator identified the urethane retainer on list, but it was not shown on the manufacturers schematic nor on my list that came with the tool. Good job by eReplacementparts. Nose cushion wore out and was easy to replace.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Nailer
Parts Used:
Urethane Retainer - 890725
Pin - 890724
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
, No tool required
Original pin on my nail gun lost the retainer clip then the pinon the trigger.
Simply inserted the new pin and placed the retaining clip on the end.

The biggest challenge was finding a replacement part. Your site made it simple.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Discussion
Discussion for Urethane Retainer - ( 890725 )
Discussion is closed. To ask our experts a question about a part, use the Q&A feature.
Question: Retainer

1281624

where does it fit this retainer ?
WJA
Hello 1281624,

Would you be able to post the model number of the tool you are working on. Hopefully if we had the model we would be able to answer your question.

-WJA
Question: Urethane Retainer 890725

1272739

How to install?
Question: Urethane Retainer - ( 890725

barbarron

Is this what holds the pin(Item 217) in place?
Hi barbarron,
Yes it just pushes over the pin. Hope that helps.Good luck.
Tinker
Reviews
4.3
Average Rating (out of 5):
4 Reviews
Click to filter by ratings:
5 stars
3
4 stars
0
3 stars
0
2 stars
1
1 stars
0
  • Highest Rating
  • Most Recent
< PREV
  • 1
NEXT >
  • Nail Gun Trigger
    I found the part easily on the site diagram and was easily installed. I thought I had lost the c clip but by watching the video I saw that it was this urethane retainer that needed replaced. Ordering was easy, shipment was relatively quick, and my nail gun’s trigger is again in place.
    Guest - May 3, 2019 Verified Purchase
    Porter Cable nail gun part
    Was quick and easy, part arrived on time. Staff friendly and helpful during ordering process. Thank you
    Guest - May 2, 2019 Verified Purchase
    Better quality than I was expecting and installation was easy as it gets. Nail gun fires fine now.
    Small retaining ring that holds one end of the pin the trigger mechanism pivots on. Easy replacement, just push onto pin and it snaps flush.
    Guest - April 19, 2019 Verified Purchase
    Not what was needed
    Your site lists problems and normal parts ordered to fix them. I ordered the three that even remotely connected to my problem. Nope!!!
    fred - 21 days ago Verified Purchase
    eReplacementParts Team
    Hi Fred, Thank you for your review. Please accept our apologies that the parts you ordered did not fix the issue with your equipment. We have responded to you privately regarding this situation.
    Verified Purchase
    eReplacementParts Team
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    NEXT >
    visa mastercard discover american express PayPal
    HACKER SAFE certified sites prevent over 99.9% of hacker crime.

    fancyboxy