Easy
15-30 minutes
It is a genuine manufacturer-supplied item that is made for DeLonghi espresso machines. Gaskets are commonly utilized to provide an air-tight seal between connected components. Unfortunately, over time the material will wear out and it may begin to crack eventually requiring a replacement. Check the diagrams for your model to ensure the correct repair procedure. A screwdriver will be needed to take apart and reassemble the housing.
Bottom Gasket AS00005075
OEM part for: DeLonghi
Part Number: AS00005075
$8.32
In Stock
Order within the next 2 hours and your part ships today! 
Jump To:
Frequently Purchased Together ?
Compatibility
This part will fit the following 9 machines
DeLonghi
EC860 Espresso Machine View Diagrams & Manuals
EC685W Dedica Deluxe Manual Espresso Machine View Diagrams & Manuals
EC860 Dedica Cappuccino Maker View Diagrams & Manuals
EC685BK Dedica Deluxe Manual Espresso Machine View Diagrams & Manuals
EC680R Dedica Manual Espresso Machine Red View Diagrams & Manuals
EC680BK Dedica Manual Espresso Machine Black View Diagrams & Manuals
EC685R Dedica Deluxe Manual Espresso Machine View Diagrams & Manuals
EC680M Dedica Manual Espresso Machine View Diagrams & Manuals
EC685M Dedica Deluxe Manual Espresso Machine View Diagrams & Manuals
Show More Compatible Models
This item works with the following types of products:
- Espresso Parts
This part replaces obsolete part #: 5313221491
Customer Part Reviews ?
Average Rating (out of 5):
Click to filter by ratings:
5 stars
1
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
Couldn't have been easier
Ordering from eReplacementParts was quick and easy, and the parts arrived in just a couple of days. Couldn't have been better, thanks. (This was an experiment to see if a new gasket would fix a minor leak in my DeLonghi espresso machine: nope, but it was worth a try. The machine still makes a good espresso, it just drips a bit around the portafilter.)
Guest -
May 6, 2021
Verified Purchase
t
t
t -
t days ago
Verified Purchase
eReplacementParts Team
t
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Bottom Gasket
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
The espresso machine needed a new group head gasket after 4 years of use.
Pasquale - February 27, 2017
👍 3 of 3 people found this instruction helpful
Tool Type
Coffee Maker
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
Parts Used
1. Unscrew the upper filter screen retaining screw and remove screen.
2. Remove the old gasket with a small flat head screwdriver.
3. Install the new gasket.
4. Replace the filter screen and reinstall the retaining screw.
5. Make espresso!
2. Remove the old gasket with a small flat head screwdriver.
3. Install the new gasket.
4. Replace the filter screen and reinstall the retaining screw.
5. Make espresso!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Dedica coffee espresso leaking inside
Alberto - June 10, 2021
Tool Type
Coffee Maker
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Pliers
Parts Used
I discovered the machine was leaking water when brewing.
I open the top cover of the machine to see inside and discovered a very small leak that when the machine was brewing with the pressure a very tiny hole was on the Y tube of water distribution.
replacement shows every part on the machine, ordered it and now is Like new!
if you are handy easy to repair
around 30 mins
I open the top cover of the machine to see inside and discovered a very small leak that when the machine was brewing with the pressure a very tiny hole was on the Y tube of water distribution.
replacement shows every part on the machine, ordered it and now is Like new!
if you are handy easy to repair
around 30 mins
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Leaking Y connector on Espresso machine
Matthew - February 25, 2020
Tool Type
Coffee Maker
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver, Pliers
Removed the upper cover, removed hose securing clips with pliers, unscrewed mounting screws to cracked part, replaced o-rings and main coffee pressure pod gasket, replaced Cracked Y part, reassembled.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Change the gasket
Juan - December 31, 2019
Tool Type
Coffee Maker
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver
Just change the old gasket for the new one
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Connector broken by the mold seam and the main gasket at coffee filter is crack, on a DeLonghi EC685R.
Jorge - April 4, 2019
Tool Type
Coffee Maker
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
DeLonghi EC685R with connector and filter gasket broken.
Parts used (from a model EC860):
1 x Gasket [ 537177 ]
1 x Gasket [ 5313221491 ]
1 x Connector [ 5313222031 ]
Instructions:
1. Disconnect power.
2. Remove the water tank.
3. Remove the two Phillips screw (bit #2) from chrome top of the machine.
4. Slide a bit back and pull up at the same time, to remove this top.
5. Disengage (pull out) knob of vapor control (knob at right side).
6. Loose the two Phillips that attach electronic of vapor control, and move carefully to one side.
7. Then you will see the connector at the bottom, attach with two Phillips.
8. Remove Phillips and disengage the two tubings connected.
9. To disconnect each tubing, pull the safety pin and pull out the tubing. Take care of the little o-ring that supposes be attach at the tip of each tubing, but frequently keep trap on connector hole.
10. Remove connector with the red o-ring, be careful with the spring with a round plastic tip, that is located below him.
11. Return this spring to the hole, with the plastic tip looking upward. Then place the new connector with a new red o-ring.
12. Go back in steps, from step 9 to step 3. That's all!!!
Parts used (from a model EC860):
1 x Gasket [ 537177 ]
1 x Gasket [ 5313221491 ]
1 x Connector [ 5313222031 ]
Instructions:
1. Disconnect power.
2. Remove the water tank.
3. Remove the two Phillips screw (bit #2) from chrome top of the machine.
4. Slide a bit back and pull up at the same time, to remove this top.
5. Disengage (pull out) knob of vapor control (knob at right side).
6. Loose the two Phillips that attach electronic of vapor control, and move carefully to one side.
7. Then you will see the connector at the bottom, attach with two Phillips.
8. Remove Phillips and disengage the two tubings connected.
9. To disconnect each tubing, pull the safety pin and pull out the tubing. Take care of the little o-ring that supposes be attach at the tip of each tubing, but frequently keep trap on connector hole.
10. Remove connector with the red o-ring, be careful with the spring with a round plastic tip, that is located below him.
11. Return this spring to the hole, with the plastic tip looking upward. Then place the new connector with a new red o-ring.
12. Go back in steps, from step 9 to step 3. That's all!!!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
The coffee maker wil spill all over
Ginette - March 29, 2019
Tool Type
Coffee Maker
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
Parts Used
1. Replaced the silicon gasket that was damaged.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
