
We Sell Only Genuine DeWALT® Parts.
DeWALT Misc Tool Parts & Models
Popular DeWALT Misc Tool Parts

This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the new cord wires to go correctly into wire terminals also routing the cord and wires in the right path can help avoid pinching when the tool case (Plate) is put back into place.

This is a genuine manufacturer-supplied replacement which is specially designed for use with DeWALT and Black and Decker saws. The purpose of a brush is to conduct the current in an electric motor that powers the tool. Unfortunately, the material will wear out and it may cause intermittent performance eventually requiring a replacement. Keep in mind this high-quality brush is sold individually When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.
Not sure if your carbon brush is causing your motor problems? See our power tool repair article: Whodunnit? The brushes or the switch?
Genuine Dewalt replacement part.
This brush is sold individually, 2 are needed for the tools shown below.
It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that’s operating intermittently. New brushes can restore a motor’s electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems. Sold individually.

The 151281-08 Pad is used to hold 5 inch Hook and Loop sandpaper with 8 vacuum holes.
Over the past few years the popularity of Hook and Loop paper has grown because of the ease of changing sandpaper when needed. Over that of the PSA (Pressure Sensitive Sandpaper)
Applying too much pressure on the sander may cause premature wear on the Hook and Loop pad.
When a pad needs to be replaced, simply remove the three screws that hold the pad to the sander, then replace it with a new pad.

Genuine OEM replacement
This brush is sold individually, 2 are needed for this tool
It is always best to replace both brushes, even if only one is worn.
Worn brushes frequently are the cause behind a motor running poorly.
Replacing brushes can fix a motor that’s operating intermittently.
New brushes can restore a motor’s electric braking.
Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.
There are over 120 tool that use this brush.

Genuine Dewalt replacement part used on Small Angle Grinder. This brush has a lead wire attached and it is Sold Individually. It is always best to replace both brushes, even if only one is worn.
Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the new cord wires to go correctly into wire terminals also routing the cord and wires in the right path can help avoid pinching when the tool case (Plate) is put back into place.

This is a genuine manufacturer-supplied replacement which is specially designed for use with DeWALT and Black and Decker saws. The purpose of a brush is to conduct the current in an electric motor that powers the tool. Unfortunately, the material will wear out and it may cause intermittent performance eventually requiring a replacement. Keep in mind this high-quality brush is sold individually When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.
Not sure if your carbon brush is causing your motor problems? See our power tool repair article: Whodunnit? The brushes or the switch?
Genuine Dewalt replacement part.
This brush is sold individually, 2 are needed for the tools shown below.
It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that’s operating intermittently. New brushes can restore a motor’s electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems. Sold individually.

The 151281-08 Pad is used to hold 5 inch Hook and Loop sandpaper with 8 vacuum holes.
Over the past few years the popularity of Hook and Loop paper has grown because of the ease of changing sandpaper when needed. Over that of the PSA (Pressure Sensitive Sandpaper)
Applying too much pressure on the sander may cause premature wear on the Hook and Loop pad.
When a pad needs to be replaced, simply remove the three screws that hold the pad to the sander, then replace it with a new pad.

Genuine OEM replacement
This brush is sold individually, 2 are needed for this tool
It is always best to replace both brushes, even if only one is worn.
Worn brushes frequently are the cause behind a motor running poorly.
Replacing brushes can fix a motor that’s operating intermittently.
New brushes can restore a motor’s electric braking.
Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.
There are over 120 tool that use this brush.

Genuine Dewalt replacement part used on Small Angle Grinder. This brush has a lead wire attached and it is Sold Individually. It is always best to replace both brushes, even if only one is worn.
Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.