fancyboxy
eReplacementParts.com
866-322-9842
Skil Parts
Repair Parts Home  Power Tool Parts  Skil Parts  1619X08308 Cord Guard

Cord Guard

Part Number: 1619X08308
SkilBosch
Availability: Special Order [ more info ]
Price: $3.99
Quantity:
Leaves our warehouse within
5 - 11 business days.

*This part replaces obsolete part #: 1619X02971, 2610005971, 1619X00943 and 2610005970.

Product Information
Manufacturer: Skil, Bosch
Product Number: 1619X08308
Classification: Part
Weight: 0.01 lbs.
Also Known As: Strain Relief, Cord Protector, Cord Cover, Cord Grip
Shipping: Ships Worldwide
Description:
  • This cord guard is a genuine Skil replacement part and is sold individually.
  • Cord guards, also called cord protectors, are designed to slide onto your cord and fit securely at the end, where it’s firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.
  • This cord guard will fit cords for the tools listed under the “Compatible Tools” listing. It is not guaranteed to fit any other cords.
  • Compatibility

    This part is compatible with the following machines:

    Skil
    Bosch

    Products Compatibility

    This item works with the following types of products:

    • • Circular Saw
    • • Saw
    Questions & Answers

    No questions have been asked yet
    Repair Instructions: Submitted by Customers Like You
    4 of 4 people found this instruction helpful
    Tool Type:
    Circular Saw
    Parts Used:
    Cord Guard - 1619X08308
    Carbon Brush Set - 1619X08020
    Power Cord - 1619X08527
    Skilsaw Worm Drive Saw Oil (8OZ) - 2610080111
    Repair Difficulty:
    Easy
    Time Spent Repairing:
    15-30 minutes
    Tools Used:
    Screwdriver
    30-year old Skilsaw needed a little maintenance. ereplacementparts were perfect.
    Remove the screws from the handle assembly, then unscrew switch from handle and remove the cord clamp. Remove the cord leads from the switch and the ground wire. Discard old cord. Slide the new cord relief onto the new cord. Install the cord leads on the switch , then the ground lead. Attach switch to handle , then put the cord clamp back on. Press the handle together. Make sure there are no wires being pinched, then install the handle on to the saw. To replace the brushes. Remove the brush caps with a screwdriver, then remove the old brushes. Install the new brushes, then screw the brush caps back on. Check oil level in the saw and add more if needed.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!
    1 of 1 people found this instruction helpful
    Tool Type:
    Circular Saw
    Parts Used:
    Cord Guard - 1619X08308
    Power Cord - 1619X08527
    Nameplate - 2610904562
    Repair Difficulty:
    Easy
    Time Spent Repairing:
    Less than 15 minutes
    Tools Used:
    Screwdriver, Torx Bits and DeWalt Impact Gun
    Replaced dry rotted cord and cord guard on my newly acquired 77HD Skilsaw
    First I removed the screws from the handle on my 77HD Skilsaw, then I removed the screws from the strain relief and the switch. I then unscrewed the positive and negative leads from the switch and the ground screw from the body of the saw. Pulled the old cord and cord guard out and replaced with the new ones, replaced the leads on the wire, making sure I routed everything properly, tightened all the mounting screws to the proper torque, put the handle back on and tested the function of the saw. Worked perfectly!
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!
    Tool Type:
    Circular Saw
    Parts Used:
    Cord Guard - 1619X08308
    Pistol Grip Handle - 1619X01363
    Repair Difficulty:
    Easy
    Time Spent Repairing:
    Less than 15 minutes
    Tools Used:
    Screwdriver
    Handle was cracked and cord guard ripped
    Unscrewed the old handle from saw removed cord end and trigger, installed handle slid cord guard over cord, reinstalled trigger in new handle, installed cover handle, finely installed all of the screws in handle.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!
    Tool Type:
    Circular Saw
    Parts Used:
    Screw - 2610315380
    On-Off Trigger Switch - 2610321608
    Cord Guard - 1619X08308
    Locking Lever - 1619X01235
    Bearing Tub - WH2X1198
    Repair Difficulty:
    Easy
    Time Spent Repairing:
    15-30 minutes
    Tools Used:
    Screwdriver, Torks tip screw driver
    Table bent after dropping saw. Handle cracked. Trigger was not working correctly causing a safety issue.
    Unscrew handle halves. Remove screws holding handle to saw and remove. Unscrew wires to trigger and remove. Screw handle half to saw that holds trigger. Install trigger wires to new switch and install into handle. Tuck in the wires as not to get pinched and install second half of handle and screw together. Install screws to a fix handle to saw. Table or foot repair starts with removing depth adjustment screw by removing retaining clip then handle and increasing nut. Remove nut at front of saw at the table. Remove table. Position table onto saw body and screw front screw and nut. Position rear adjustment arch into threaded stud and replace nut. Adjust the nut so the Table can go up and down. Position the lever so down is tight and up loosens enough to adjust depth. Install keeper e clip. On old table remove adjustment nut and install on new table. Just reverse the process to install. Done. Now the saw will cut square and the honey dos will go easy.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!
    Tool Type:
    Circular Saw
    Parts Used:
    Cord Guard - 1619X08308
    Power Cord - 1619X08527
    Handle - 1619X01364
    Handle Assembly - 1619X01423
    Repair Difficulty:
    Easy
    Time Spent Repairing:
    15-30 minutes
    Tools Used:
    Socket set, Torks bit set and 1/4\\
    Saw was dropped and fractured handles
    Removed handle half on main grip, took picture for reference with phone to reference wiring on the switch, detached ground to motor case, removed switch and old cord and guard, transferred switch and attached new cord and guard to new grip half, removed old grip half and installed new grip half assembly and attached ground other new grip half and new top handle.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!
    Tool Type:
    Circular Saw
    Parts Used:
    Cord Guard - 1619X08308
    Power Cord - 1619X08527
    Repair Difficulty:
    Easy
    Time Spent Repairing:
    15-30 minutes
    Tools Used:
    Screwdriver
    Bad cord on a skilsaw
    Removed handle and replace cord and cord guard
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!
    Tool Type:
    Circular Saw
    Parts Used:
    Cord Guard - 1619X08308
    Carbon Brush Set - 1619X08020
    Power Cord - 1619X08527
    Repair Difficulty:
    Medium
    Time Spent Repairing:
    15-30 minutes
    Tools Used:
    Screwdriver
    A lot of sparking in the motor; short cord.
    Removed covers for brushes then replaced old brushes with new ones. Removed screws from handle assembly then removed screws holding terminals on old power cord. Replaced old cord with new one and replaced the screws. My vintage Skilsaw 825 worm drive is ready for another 50 years of use!
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!
    Tool Type:
    Circular Saw
    Parts Used:
    Cord Guard - 1619X08308
    Carbon Brush Set - 1619X08020
    Repair Difficulty:
    Easy
    Time Spent Repairing:
    30-60 minutes
    Tools Used:
    Screwdriver, Pliers
    Sparking from brushes and burning smell. Cord guard was split.
    1. On either side of saw there are plastic set screws which you remove and brushes pop right out.
    2. Install new brushes. Very easy.
    Cord guard a little more difficult.
    1. Have to remove screws and open saw.
    2. Remove cord and old guard.
    3. Install new guard with cord and re-assemble
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!
    Tool Type:
    Circular Saw
    Parts Used:
    On-Off Trigger Switch - 2610321608
    Cord Guard - 1619X08308
    Repair Difficulty:
    Easy
    Time Spent Repairing:
    15-30 minutes
    Tools Used:
    , Allen wrench
    Start switch and cord strain relief broken
    1). Used allen wrench to remove handle from saw body and separate into two halves
    2). Used smaller allen wrench to unfasten start switch from housing
    3). Used screwdriver to remove wires from start switch. Replacement switch though similar ran wires in slightly different pattern. Used ohm meter to verify correct contacts.
    4). Old cord strain relief was removed and new one inserted and clamped to original mount using screwdriver.
    5). Wires were reattached to new switch and then reattached switch to handle housing using Allen wrench.
    6). Handle housing halves were reattached to each other and inserted into saw frame. All mounting screws were reinstalled.
    7). Tested saw for running mode . Saw ran correctly and then installed new saw blade.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!
    Tool Type:
    Circular Saw
    Parts Used:
    Cord Guard - 1619X08308
    Power Cord - 1619X08527
    Repair Difficulty:
    Easy
    Time Spent Repairing:
    Less than 15 minutes
    Tools Used:
    Screwdriver, Torx bit
    broken ground, dryrot cord relief
    Removed handle half, removed ground screw, removed switch, removed cord from switch, removed cord anchor screws, Installed new cord with cord relief and re-assemble handle.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!
    Discussion
    Discussion for Cord Guard - ( 1619X08308 )
    Discussion is closed. To ask our experts a question about a part, use the Q&A feature.
    Reviews
    5
    Average Rating (out of 5):
    4 Reviews
    Click to filter by ratings:
    5 stars
    4
    4 stars
    0
    3 stars
    0
    2 stars
    0
    1 stars
    0
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    NEXT >
  • works as described
    Part works great, just wish Ereplacement would ship using anyone other than Fedex, slower than USPS
    Ronald - 18 days ago Verified Purchase
    Exact Match
    This was a perfect replacement part & was very easy to install!
    Guest - May 30, 2019 Verified Purchase
    Good
    Parts came on time and look to be decent quality. I had another item in my cart that was dropped without my notice and thus needed but not purchased. Maybe cart system could use a tune up.
    Raymond - May 8, 2019 Verified Purchase
    Fits perfectly
    i replaced the handle, power cord and cord guard on my 25yo Skil saw. Everything fit together exactly as it should. Is needed to prevent the cord breaking right next to the handle.
    Guest - April 25, 2019 Verified Purchase
    Verified Purchase
    eReplacementParts Team
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    NEXT >
    Product Information
    Manufacturer: Skil, Bosch
    Product Number: 1619X08308
    Classification: Part
    Weight: 0.01 lbs.
    Also Known As: Strain Relief, Cord Protector, Cord Cover, Cord Grip
    Shipping: Ships Worldwide
    Repair Guides
    Watch the Repair Video for Cord Guard
    How to Replace the Cord Guard on a Skilsaw
    Articles:
    How to Replace the Cord Guard on a Skilsaw
    Step-by-step instructions for removing and installing the cord guard on your Skilsaw....
    October 09, 2017
    Related Products
    eReplacementParts.com
    7036 South High Tech Dr.
    Midvale, UT 84047
    visa mastercard discover american express PayPal