Easy
15-30 minutes
This item is an original Makita replacement part that is intended to be used with finishing sanders. The clamper attaches to the back of the sanding pad and is used to secure sandpaper sheets to the pad. This part is priced as a single item, please note two clampers may be needed.
Clamper 342986-5
OEM part for: Makita
Part Number: 342986-5
$3.99
In Stock
Order within the next 12 hours and your part ships today! 
Jump To:
Frequently Purchased Together ?
Compatibility
This Clamper will fit the following 2 machines. Confirm this part works with your model, and view the detailed model diagrams and repair help we have to offer.
Displaying 2 of 2 matching models.
2 total model matches. Try the above search to narrow your results.
This is the official OEM part for the following brands:
- Makita
This item works with the following types of products:
- Sander
Customer Part Reviews ?
Average Rating (out of 5):
Click to filter by ratings:
5 stars
6
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
Part fit perfectly
Finish sander is as good as new. Was worthless without the clamper.
Guest -
July 25, 2023
Verified Purchase
Parts for DeWalt sander
I was a perfect fit and arrived quick, Thanks
Guest -
July 23, 2022
Verified Purchase
Just as expected.
Fast and furious! Well done - parts are installed and working great!
Guest -
December 14, 2021
Verified Purchase
Good
Easy to use website
Guest -
February 6, 2021
Verified Purchase
Excellent Service
The part was priced great, shipping was quick, the old part was replaced in minutes. Works great.
Guest -
July 29, 2020
Verified Purchase
Easy repair
The parts fit perfectly couldn’t be happier
Guest -
June 6, 2019
Verified Purchase
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Clamper
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
THE JAWS ON MY MAKITA SANDER WOULD NO LONGER GRASP THE SANDPAPER
Timothy - December 20, 2015
👍 5 of 5 people found this instruction helpful
Tool Type
Sander
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
Parts Used
THE TEETH WERE WORN DOWN ON THE JAWS AND NOT GRABBING THE SANDPAPER. THE SANDPAPER WAS COMING OFF MY MAKITA OSCILLATING PALM SANDER. I HAD IT SINCE THE 80'S I THINK. BUT THERE IS NOTHING ELSE WRONG WITH IT SO WHY NOT REVIVE IT?
REMOVE THE FOUR SCREWS IN THE BOTTOM OF THE PAD, AND FLIP THE LEVERS SO THERE IS NO PRESSURE ON THE JAWS. I HAD TO WIGGLE THE PAD SO THE TABS ON THE JAWS WOULD SLIP OUT FROM UNDER WHERE THEY FIT WHEN THE THING IS ASSEMBLED.
BUT I DID NOT HAVE TO REMOVE ANYTHING ELSE IN ORDER TO REMOVE THE OLD AND PUT IN THE NEW. COOL..
REMOVE THE FOUR SCREWS IN THE BOTTOM OF THE PAD, AND FLIP THE LEVERS SO THERE IS NO PRESSURE ON THE JAWS. I HAD TO WIGGLE THE PAD SO THE TABS ON THE JAWS WOULD SLIP OUT FROM UNDER WHERE THEY FIT WHEN THE THING IS ASSEMBLED.
BUT I DID NOT HAVE TO REMOVE ANYTHING ELSE IN ORDER TO REMOVE THE OLD AND PUT IN THE NEW. COOL..
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Normal wear and tear.
Tom - April 15, 2016
👍 2 of 2 people found this instruction helpful
Tool Type
Sander
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Pliers, nonCompressed air
Parts Used
1. Removed the old self stick pad.
2. Unscrewed the base plate
3. Disassembled the hold down clampers.
4. Blew out the dust.
5. Installed new clampers and base plate.
6. Install new sponge rubber pad.
2. Unscrewed the base plate
3. Disassembled the hold down clampers.
4. Blew out the dust.
5. Installed new clampers and base plate.
6. Install new sponge rubber pad.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Grabber teeth wore down.
Jim - December 8, 2016
👍 1 of 1 people found this instruction helpful
Tool Type
Sander
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
Parts Used
Removed sanding pad, removed the old clamps and installed the new clamps. Then installed the pad.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Refurb an older Makita BO4550 sander
David - August 7, 2023
Tool Type
Sander
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver, Pliers
Parts Used
Picked this up used sander to complete a refinishing project. It's an oldie but goodie. It had good bones, extremely well constructed. Ultimately I replaced the sandpaper clamps and retaining clips, the nylon feet that hold the base, the brushes and a seal.
Cleanup was extensive, I used 600 grit wet/dry paper VERY lightly on the armature to remove accumulated oxidation. All the bearings were tight, no attention needed.
Assembled the old sander, fortunately there are plenty of sources of exploded parts list to make sure you gat it back together properly.
In the end, I now have a Makita 1/4 sheet sander that runs like brand new and since all the wearable parts have been replaced should last a very long time. You would be hard pressed to find a new unit with this quality unless you plan to spend a great deal.
Cleanup was extensive, I used 600 grit wet/dry paper VERY lightly on the armature to remove accumulated oxidation. All the bearings were tight, no attention needed.
Assembled the old sander, fortunately there are plenty of sources of exploded parts list to make sure you gat it back together properly.
In the end, I now have a Makita 1/4 sheet sander that runs like brand new and since all the wearable parts have been replaced should last a very long time. You would be hard pressed to find a new unit with this quality unless you plan to spend a great deal.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
sander would not run
Slotteo - April 15, 2019
Tool Type
Sander
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, none
took the sander apart and put in new parts.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Was making a lot of noise not not sanding well
Ernest - March 30, 2018
Tool Type
Sander
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver
Just replaced old worn out parts with the new ones. Now it works like new.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Would not hold sandpaper.
RALPH - October 7, 2017
Tool Type
Sander
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
Parts Used
1. Removed 4 screws from the bottom plate.
2. Removed the old clamps.
3. Replaced the clamps.
4. Replaced 4 screws.
2. Removed the old clamps.
3. Replaced the clamps.
4. Replaced 4 screws.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Pad and lever replacement
Eunice - August 31, 2017
Tool Type
Sander
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
Replaced pad and lever on sander with screw driver
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Learn MoreOur product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
