866-322-9842
Mon-Fri 7am-1am EST
Sat-Sun 7am-11pm EST
Repair Parts Home  Power Tool Parts  Makita Parts  CB440 Carbon Brush Set

Carbon Brush Set

Part Number: CB440
Makita
Availability: 25+ in stock
Price: $4.69
Quantity:
Ships within 1 business day

*This part replaces obsolete part #: 195021-6, 194427-5 and 194159-4.

Description:
Genuine Makita replacement part
Set of 2 Carbon Brushes with wire lead attached. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that’s operating intermittently. • New brushes can restore a motor’s electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.
Product Information
Manufacturer: Makita
Product Number: CB440
Classification: Part
Weight: 0.01 lbs.
Also Known As: Motor Brush Set
Shipping: Ships Worldwide
Repair Guides
Articles:
How to Replace the Carbon Brush Set on a Makita Cordless Hammer Drill (Model LXPH01)
Motor brushes bad? Replace them in under 5 minutes. Step-by-step instructions show you how. ...
April 19, 2016
Compatibility

This part is compatible with the following machines:

Makita
LXFD01CW 18V Compact Lithium-Ion Cordless 1/2" Driver-Drill
LXFD01 18V LXT Lithium-Ion Cordless 1/2" Driver-Drill
LXFD01 18V LXT Lithium-Ion Cordless 1/2" Driver-Drill
LXFD01Z 18V LXT Lithium-Ion Cordless 1/2" Driver-Drill
LXFD01Z 18V LXT Lithium-Ion Cordless 1/2" Driver-Drill
LXSF01 18V LXT Lithium-Ion Cordless Drywall Screwdriver
LXPH01 18V LXT Lithium-Ion Cordless 1/2 Hammer Driver-Drill Kit
LXPH01 18V LXT Lithium-Ion Cordless 1/2 Hammer Driver-Drill Kit
LXPH01 18V LXT Lithium-Ion Cordless 1/2 Hammer Driver-Drill Kit
LXPH01Z 18V LXT Lithium-Ion Cordless 1/2 Hammer Driver-Drill
LXPH01Z 18V LXT Lithium-Ion Cordless 1/2 Hammer Driver-Drill
LXPH01Z 18V LXT Lithium-Ion Cordless 1/2 Hammer Driver-Drill
LXPH01CW 18V LXT Lithium-Ion Cordless 1/2 Hammer Driver-Drill
LXPH01CW 18V LXT Lithium-Ion Cordless 1/2 Hammer Driver-Drill
LXPH01CW 18V LXT Lithium-Ion Cordless 1/2 Hammer Driver-Drill
LXDT04 18V LXT Lithium-Ion Cordless Impact Driver Kit
LXSF01Z 18V LXT Lithium-Ion Cordless Drywall Screwdriver
LXDT04CW Cordless Impact Driver
LXPH03 18V Hamer Driver-Drill
XFD01 18V LXT Lithium-Ion Cordless 1/2" Driver-Drill Kit
XFD01 18V LXT Lithium-Ion Cordless 1/2" Driver-Drill Kit
XFD01RW 18V Compact Lithium-Ion Cordless 1/2" Driver-Drill Kit
XFD01RW 18V Compact Lithium-Ion Cordless 1/2" Driver-Drill Kit
XPH01RW 18V Compact Lithium-Ion Cordless 1/2" Hammer Driver-Drill Kit
XPH01RW 18V Compact Lithium-Ion Cordless 1/2" Hammer Driver-Drill Kit
XPH01RW 18V Compact Lithium-Ion Cordless 1/2" Hammer Driver-Drill Kit
XPH03M 18V LXT Lithium-Ion Cordless 1/2" Hammer Driver-Drill Kit
XPH03M 18V LXT Lithium-Ion Cordless 1/2" Hammer Driver-Drill Kit
XPH03M 18V LXT Lithium-Ion Cordless 1/2" Hammer Driver-Drill Kit
XPH01 18V LXT Lithium-Ion Cordlesss 1/2" Hammer Driver-Drill
XPH01 18V LXT Lithium-Ion Cordlesss 1/2" Hammer Driver-Drill
XPH01 18V LXT Lithium-Ion Cordlesss 1/2" Hammer Driver-Drill

Products Compatibility

This item works with the following types of products:

  • • Cordless Drill
  • • Drill
  • • Hammer Drill
  • • Impact Driver
  • • Impact Wrench
  • • Screwdriver
  • • Shear
Expand List
Questions & Answers

Need the plugs that are on both sides of Hammer Drill holds the brush in place
Raul Gomez for model number 527047 E
Hello Raul, thank you for inquiring. That is the Holder Cap for your model and it is part 643933-2. They are sold individually.
Repair Instructions: Submitted by Customers Like You
15 of 15 people found this instruction helpful
Tool Type:
Cordless Drill
Parts Used:
Carbon Brush Set - CB440
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Brushes worn out, gun wouldn't work properly.
Small screwdriver, pointed object, such as knife blade or an awl. Remove screws from the rear cover. Pull spring keeper back, remove brush. use pointed tool to pop off clip. Pull back spring keeper insert new brush. Pop on new clip. x2, done
Did you find this story helpful?
Thanks for voting and helping fellow customers!
6 of 7 people found this instruction helpful
Tool Type:
Cordless Drill
Parts Used:
Change Lever - 419250-0
Carbon Brush Set - CB440
Switch TG553FSB-4 - 650573-9
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Switch stuck, Brushes worn, Lever broke due to Switch Hanging up.
Remove cover,
Make a wiring diagram, remove old switch, install the new switch
Disconnect the old brushes then, connect the new ones
Remove Forward Reverse lever and install new
Install cover
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 3 people found this instruction helpful
Tool Type:
Impact Driver
Parts Used:
Carbon Brush Set - CB440
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Pliers
Switch would not turn on drill every time.
Thought it might have been the switch but the suggested solution for the problem I was having was replace brushes (75% vs 12%) and that's exactly what it was.
Remove two screws from back of drill housing.
Lift retainer spring off of brush with nail or screw.
Pull worn brush out by wire with needle nose pliers and remove clamp at other end of wire.
Do the same in reverse order to install new brushes
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Cordless Drill
Parts Used:
Carbon Brush Set - CB440
Brush Holder - 638614-1
Armature - 619496-0
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Drill would not turn.
1. Took apart the drill
2. Replaced the broken parts.
3. Reassembled the drill.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Cordless Drill
Parts Used:
Carbon Brush Set - CB440
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Both the Impact and Drill were several years old, and I figured the brushes were in need of replacement
Removed the two screws on the back of the Drill/Driver
Removed the end cap
Pried the clip up that held the wire
Carefully pried the retaining spring away from the brushes, and removed them one at a time.
Slide the new brushes in place.
Routed the wire around the brush holder, and secured the retaining clip.
Re-installed the end cap, careful to align the bearing on the shaft with the cut out on the cap, and replaced the two screws.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Cordless Drill
Parts Used:
Carbon Brush Set - CB440
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Right angel pick
Runs hot, starts to run slow and sporadicly and then not at all
1. Removed the four screws on the right angle head
2. Pulled off spacer between the head and main tool body
3. Removed the four smaller screws from the right side of the tool
4. Removed the right half of the tool
5. Pull up on the brush "ring" up just enough to have access to both brushes
6. Note the direction the wire from the clips to the brush itself
7. Use the right angle pick tool to pry up the clips.
8. Use the same tool to move the spring arm that holds the brush to the armature. Use the very small divet on the side of the brush holder to hold the spring arm.
9. Remove and reinstall the new brushes, make sure the spring arm is back holding the brush.
10. Slide the brush ring back into place, reinstall the side, spacer and right angle head.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Cordless Drill
Parts Used:
Carbon Brush Set - CB440
Brush Holder - 638614-1
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pick tool
Slow & didn't start
Removed the 2 phillips end cap screws to access the brushes. They simply pull out to the holder after I took a pick and held the brush spring off to the side. When replacing the holder you have to separate the two halves of the handle. Not a big job. Just make sure you line up the steel field that the armature turns in. It has a notch in it that has to line up with the one in the handle housing. If you don't do this you can't get the housings completely together and wonder why. This happened to me. Also make sure the detent springs for the High/Low don't fall out when putting the two halves together. Otherwise it was a simple repair. I have done 2 drills so far in our business and plan to get more parts to do more. Parts are identical to the original and are in Makita labeled packaging. Also great pricing.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Drill
Parts Used:
Carbon Brush Set - CB440
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Replace worn out carbons
Opened the drill, removed old carbons, replaced with new, closed it right back
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Impact Driver
Parts Used:
Carbon Brush Set - CB440
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Worn out brushes
Replaced brushes; easy. Just make sure to note how the old ones fit, and put the new ones in the same way
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Impact Driver
Parts Used:
Carbon Brush Set - CB440
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Super slow impact drive, noticed a wire on one side of the old brushes was broken, new brushes installed easily and drill worked good as new!
Two screws to remove, pop out old brushes, install new brushes, re-install cover with two screws, smile wide as drill is good as new!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
4.9
Average Rating (out of 5):
7 Reviews
Click to filter by ratings:
5 stars
6
4 stars
1
3 stars
0
2 stars
0
1 stars
0
  • Highest Rating
  • Most Recent
< PREV
  • 1
NEXT >
  • Right parts, fast shipping, easy transaction!
    Parts fit perfectly & got my drills going as if they were new again. Will do business again in the future.
    Guest - 0 days ago Verified Purchase
    Makita18v drill working good as new
    The new brushes did the trick. The replacement was VERY easy. Two screws, that was it. New brushes fit perfectly.
    Louis - 5 days ago Verified Purchase
    Great parts
    Thanks
    Guest - 9 days ago Verified Purchase
    Worked perfectly thank you
    Worked perfectly thank you
    Guest - May 6, 2019 Verified Purchase
    easy repair
    parts all were manufacturers brand...quick arrival
    douglas - May 2, 2019 Verified Purchase
    Easy repair based on the video
    All the parts I ordered fixed my drill and now works. The drill burnt up and had to get new parts
    Guest - April 20, 2019 Verified Purchase
    Makita brushes
    It made my screw gun works like. New.
    Guest - 6 days ago Verified Purchase
    Verified Purchase
    eReplacementParts Team
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    NEXT >
    visa mastercard discover american express PayPal
    HACKER SAFE certified sites prevent over 99.9% of hacker crime.

    fancyboxy