eReplacementParts.com
877-346-4814
Preferred Partners of
Coleman
Husqvarna
Karcher
MK Diamond
MTD
Makita Parts

Switch

Part Number: 650723-6
Makita
Availability: 25+ in stock
Price: $27.84
Ships within 1 business day

*This part replaces obsolete part #: and 650660-4.

Product Information
Manufacturer: Makita
Product Number: 650723-6
Classification: Part
Weight: 0.09 lbs.
Shipping: Ships Worldwide
Description:
This is a genuine OEM approved replacement part designed for use with Makita impact driver. Switches are a commonly replaced part in power tools, handling on/off operations. Because switches use mechanical internals, they will degrade and wear out over time, eventually requiring replacement. This switch has a plastic body.

To replace this switch you would need a screwdriver.

• First make sure the tools is not plugged in
• Then you want to remove screws used to hold two pieces of housing set together
• Disconnect wires and remove switch from the housing
• Place new switch in the housing and connect wires to it
• Reassemble the housing
Compatibility

This part is compatible with the following machines:


Products Compatibility

This item works with the following types of products:

  • • Impact Driver
Questions & Answers

No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
6 of 7 people found this instruction helpful
Tool Type:
Impact Driver
Parts Used:
Switch - 650723-6
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Intermittent trigger operation
Remove screws and split exterior case. Make a wiring diagram of where the wires are connected. Disassemble switch wiring from battery leads. Install new switch, per wiring diagram. Put back together in opposite order worked good as new
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 3 people found this instruction helpful
Tool Type:
Impact Driver
Parts Used:
Switch - 650723-6
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Impact driver
Impact driver had vary low torque.
Opened housing & checked brushes & armature. No problem found. Bypassed switch & applied power to brushes directly from the battery. Tool ran at full power & torque. Replaced switch 1 wire at a time. Tool ran normally. Reassembled in reverse order. Problem solved.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Impact Driver
Parts Used:
Switch - 650723-6
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Power Drill, Tape or marker
Impact driver variable speed touchy
Use tape or marker to mark wire positions as you remove each wire.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Impact Driver
Parts Used:
Switch - 650723-6
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
intermittent trigger switch
1. unscrewed 2 halves of impact driver body( all phillips screws, yay!).
2. removed chuck collar
3. unscrewed old trigger, slipped off blade connectors( no bare wires to connect, yay!).
4. reverse order for new trigger.
5. reverse order for body assembly(bada bing!).
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Impact Driver
Parts Used:
Switch - 650723-6
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers
Lamp would light, but driver would run.
Opened case with Philips screwdriver.
Carefully remove both end protectors.
Remove switch with fingers and/or needle nose pliers. My fingers don't function as well as they once did.
Install new identical switch and reassemble.
Voila, it works good as new.

Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Impact Driver
Parts Used:
Switch - 650723-6
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Forward - reverse switch broke
1 Removed screws fro drill
2 Unplugged switch
3 Plugged new one in
4 Put screws back in drill
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Impact Driver
Parts Used:
Switch - 650723-6
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Pliers
Loss of power and the trigger was acting up. This is for the 18v driver with the star on the battery port.
Take it apart, remember where everything goes and put it back together with the new trigger, maybe a dozen screws and some clips you may need some needle nose for.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Impact Driver
Parts Used:
Switch - 650723-6
Repair Difficulty:
Medium
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Pliers
Trigger on/off switch was broken
Removed case screws. Opened case. Removed 3 connectors. Removed switch. Replaced switch. Replaced connectors. Closed case and reinstalled screws. Really straightforward.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Impact Driver
Parts Used:
Carbon Brush Set - CB440
Switch - 650723-6
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Drill trigger go on and off
Replace trigger and brushes and works like new.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Impact Driver
Parts Used:
F/R Change Lever - 419041-9
Switch - 650723-6
Bumper - 424429-0
Hammer Case Cover - 452837-5
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers
Drill would hesitate
Take off back cover. remove all screws, take a picture of the switch to make sure you have the correct wires going to the proper terminals. Remove old switch and install new one in reverse order. While I was in there I replace the worn F/R Change Lever. Also replace missing bumper and cracked hammer case cover, they just snap on.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Discussion
Discussion for Switch - ( 650723-6 )
Discussion is closed. To ask our experts a question about a part, use the Q&A feature.
Question: Makita LXDT04 Not Working With B...

1234202

I just bought a new Makita impact driver on eBay (last time I buy a tool on ebay to save a few bucks). I bought the bare tool because I already have 2 batteries that came with my hammer drill. The driver seems to only work if I leave it about 1/8" from snapping in. The driver says it is compatible with the battery, but has a different terminal piece than my hammer drill.

I had the seller replace the driver once already before I discovered that it works when you leave the battery out a ways. Just wondering if anyone has any ideas short of sending it in to Makita.
Hi ,
The Makita LXDT04 and your BL1830 Batteries are both compatible with each other. The fact that the tool works when the battery is not fully seated and this is happening with both batteries tells me that the tool is pinging a code to the battery that tool is not reading values within certain thresholds and will not allow the tool to run.When you pull the battery part of the way out the connection which is marked"TH" on your battery is disconnected and the tool will run at safe mode.
Li-on batteries are unstable by their nature and must be carefully controlled when charging or discharging thus the cores can become unstable and create a fire hazard.Because of this the battery and tool must be communicating back and forth as to keep everything safe.
I would do this .First charge your batteries to full charge and try them in the drill.If you still have the same problem then the switch which has the circuit board built in to it will need to be replaced. And that should be done under warranty.Hope that helps.Good luck.
Tinker
Reviews
5
Average Rating (out of 5):
7 Reviews
Click to filter by ratings:
5 stars
7
4 stars
0
3 stars
0
2 stars
0
1 stars
0
  • Highest Rating
  • Most Recent
< PREV
  • 1
NEXT >
  • so far so good
    Fits perfect easier to replaced works like new again
    Guest - November 13, 2020 Verified Purchase
    I super appreciate eplacementparts.com!
    In my business, we use a lot of small power tools. E Replacement Parts is a great resource for me to order the parts I need to Keep them in operating condition. Huge parts inventory, prompt service, great prices. I highly recommend E Replacement Parts.
    Ken - September 15, 2020 Verified Purchase
    Lifesaver
    Replacement parts arrived very quick. Quick and easy repairs were done in no time with little down time.
    Guest - December 2, 2019 Verified Purchase
    Easy repairs
    Was in great condition when arrived and fits perfectly my impact driver is up and running again..
    Clifton - October 7, 2019 Verified Purchase
    Great part Great service
    Exact fit
    Guest - September 2, 2019 Verified Purchase
    easy fix for 18V makita drill
    The trigger assembly was easily swapped out in my 18V makita driver/drill
    Guest - May 23, 2019 Verified Purchase
    Perfect
    Good condition
    Guest - May 1, 2019 Verified Purchase
    Verified Purchase
    eReplacementParts Team
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    NEXT >
    Product Information
    Manufacturer: Makita
    Product Number: 650723-6
    Classification: Part
    Weight: 0.09 lbs.
    Shipping: Ships Worldwide
    eReplacementParts.com
    7036 South High Tech Dr.
    Midvale, UT 84047
    visa mastercard discover american express PayPal