Watch The
Repair Video

Armature-Magneto

Part Number: 593872

2 Reviews

Availability: 6 in stock

Price: $38.76

Order within the next 13 hours

and your part ships today!

Questions & Answers

Repair Instructions

*This part replaces obsolete part #: and 799582.

Product Information

Manufacturer: Briggs and Stratton

Product Number: 593872

Classification: Part

Weight: 0.52 lbs.

Shipping: Ships Worldwide

Description:

This is a genuine OEM sourced replacement part designed for use with gas powered string trimmers and blowers. The ignition module also known as armature-magneto is designed to produce pulses of high voltage for the spark plugs. It is made from durable metal with a rubber insulated wire and it is sold individually. Please note the spark plug boot is sold separately.

Compatibility

This part is compatible with the following machines:

Briggs and Stratton

See more of the 150+ compatible machines

Products Compatibility

This item works with the following types of products:

• Engine

Questions & Answers

Sort by

No questions have been asked yet

Repair Instructions: Submitted by Customers Like You

2 of 3 people found this instruction helpful

Tool Type:

Lawn Mower

Parts Used:

Wire-Stop - 692390

Boot-Spark Plug - 692076

Spark Plug - 692051

Armature-Magneto - 593872

Repair Difficulty:

Medium

Time Spent Repairing:

15-30 minutes

Tools Used:

Socket set

Lawn Mower runs but eventually has knocking sounds and shuts off

1. Added new fresh oil correct 15OZ amount.
2. Replaced Spark plug.
3. Replaced Air Foam Filter.
4. Replaced carburator.
5. Replaced Armature Magneto.
6. Replaced Wire Stop.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

2 of 6 people found this instruction helpful

Tool Type:

Engine

Parts Used:

Armature-Magneto - 593872

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Screwdriver, Socket set

No fire.

1. Took the housing apart.
2. Removed the old magneto.
3. Connected the new one.
4. Reassembled and tested.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Discussion

Discussion for Armature-Magneto - ( 593872 )

Discussion is closed. To ask our experts a question about a part, use the Q&A feature.

Question: Ignition Module 593872

112pumpkin

when replacing the ignition module do the ends need to contact the wheel or is the a gap requirement between ignition module and the wheel which is faces ? Not sure what you call the wheel which spins when pulling the starter cord.

Hi 112pumpkin No, the legs should NEVER contact the flywheel. There should be an AIR-GAP of about .010" (ten-thousandths of an inch) in between the coil legs and the magnets in the flywheel. Use a standard business card as a gauge. Let the flywheel magnets pull the legs into them with the card in between them. Do this with the 2 small bolts in place and almost tight. Then, tighten down the 2 small bolts and remove the business card. Be careful tightening down the bolts. Don't go too tight and wrench the heads off of them or break them. The wheel that spins is called the FLYWHEEL and has fins on it. It has a few different purposes. IT balances the engine. It times the spark to the engine. The raised fins on it act as a fan to blow air AROUND the engine cylinder for cooling when the engine shroud (cover) is installed.

Reviews

Average Rating (out of 5):

2 Reviews

Click to filter by ratings:

5 stars

4 stars

3 stars

2 stars

1 stars

Sort by:

Highest Rating
Most Recent

< PREV

NEXT >

Right part, easy install

I wasn't sure this would fix the mower. But all I could figure out was the spark plug was NOT getting any spark. I took the chance because eReplacementParts welcomes returns. But after an easy install the mower fired right up and runs like a charm now!

Rodney - July 5, 2019 Verified Purchase