It is a genuine manufacturer approved replacement part designed for use with Homelite pressure washers. This gasket creates an air-tight seal for the carburetor. Over time it may shrink, deteriorate and crack eventually requiring replacement. It is a high quality composite material/rubber gasket that is sold individually.
Air Cleaner Gasket 099980425068
OEM part for: Homelite
Part Number: 099980425068
Jump To:
Frequently Purchased Together ?
Compatibility
This part will fit the following 9 machines
Homelite
This item works with the following types of products:
- Pressure Washer Parts
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Air Cleaner Gasket
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Pressure Washer would not start.
Tool Type
Pressure Washer
Difficulty
Medium
Time
1-2 hours
Tools Used
Socket set, Wrench Set, Spark Gap Gauge
2. Put the entire Washer on a portable workbench
3. Removed wheels for easier access to mounting bolts and parts
4. unbolted motor mount for access to Nuts for housing cover for Air Breather and Carb
5. Replaced spark plug (adjusted Gap to specs)
6. Removed Air filter assembly for access to the carburetor - Disconnected and plugged fuel line
7. Disconnected throttle spring and bar
8. Removed old carb - slid off the two mounting bolts
9. replaced 1st gasket and slid on new Carb
10. reconnected, throttle spring, and bar replaced the front gasket
11. checked linkages
12. Reconnected fuel line and breather tube
12. Remounted Air Filter assembly replaced the two mounting Nuts
13. Reattached engine to the mounting bracket
14. Reattached Wheels
15. Tested and worked great
Note: it would not have been necessary to dismount the engine if there had been better clearance to the carburetor mounting nuts... Would have saved a lot of time.
Carburetor clogged with old gas
Tool Type
Pressure Washer
Difficulty
Medium
Time
15-30 minutes
Tools Used
Pliers, Socket set, Wrench Set
2. Unbolted 2 cap nuts on end of carb/air assembly/ w/choke on and gas in off position
3. Pulled off air cleaner assembly while carefully disconnecting air breather hose
4. Take off air cleaner gasket
5. Pulled gas hose off carb assembly after using pliers to slide spring clamp up 1 inch from end(drain old gas into approved container)
6. 3 bolts hold gas tank, 2 under side of tank and 1 on other side going horizontally/ remove and slowly guide gas tank up and guide fuel line out as you remove tank/ remove spring clamp and replace hose/ if gas only trickled out of hose when draining also replace tank outlet which screws into tank/ inspect inside of tank for corrosion.
7. Pull off carb assembly - inspect gasket/ replace if needed(not usually needed to change) replace with new carb assembly.
8. Put tank back on while guiding fuel tube as was originally routed and connect to carb assembly and guide block/ use pliers and move clamp back to 1/2 inch from end of tube.
9. Put air assembly gasket back on- make sure that gasket is oriented correctly to air slot on carb assembly- place choke lever on carb so that it works on the butterfly valve on carb when moved
10. Place air assembly back on and connect air breather tube back on air breather/ put cap nuts back on and tighten firmly but not too tight.
11. Put engine back in place align bolts with nuts on top and tighten firmly.
Carburetor was bad.
Tool Type
Pressure Washer
Difficulty
Easy
Time
30-60 minutes
Tools Used
Screwdriver, Pliers, Wrench Set
Engine stalling.
Tool Type
Pressure Washer
Difficulty
Medium
Time
30-60 minutes
Tools Used
Wrench Set, Nutdriver
2. Remove the carb heat shield.
3. Remove the pull rope assembly.
4. Replace the coil.
5. Replace the carb.
6. Reassemble.
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.