Medium
30-60 minutes
This is an authentic Dremel replacement part, sourced from the original manufacturer for use with rotary tools. The special brush holder is used to secure the carbon brushes, and the holder includes the lead wire that connects the brush and switch. This brush holder is available as an individual replacement part, please see model diagram for associative parts.
Brush Holder 2610003434
OEM part for: Dremel, Bosch
Part Number: 2610003434
$3.99
In Stock
Order within the next 6 hours and your part ships today! 
Jump To:
Frequently Purchased Together ?
Compatibility
This part will fit the following 2 machines
Dremel
4000 Variable-Speeds Rotary Tool View Diagrams & Manuals
4000 (F013400001) Bare Tool 120v Usa 4000 View Diagrams & Manuals
This item works with the following types of products:
- Multi-Tool Parts
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Brush Holder
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Dremel could not maintain consistent speed setting
Chance - March 22, 2018
Tool Type
MultiTool
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver, T15 TORX BIT
Replaced old brushes along with
Specifically
1. Remove power cord from wall
2. Unscrewed the two flathead screws securing the brushes inside
3. Pulled brushes from each side
4. Removed the 5 or 6 T15 TORX screws
5. Removed collar on drive shaft and hanging bracket from the rear
6. Took top off and notated which wires went where.
7. Removed the two brush holders and replaced with new ones
8. Reassembled and tested
Specifically
1. Remove power cord from wall
2. Unscrewed the two flathead screws securing the brushes inside
3. Pulled brushes from each side
4. Removed the 5 or 6 T15 TORX screws
5. Removed collar on drive shaft and hanging bracket from the rear
6. Took top off and notated which wires went where.
7. Removed the two brush holders and replaced with new ones
8. Reassembled and tested
Did you find this story helpful?
Thanks for voting and helping fellow customers!
The unit locked up 10 yrs ago while cutting aluminum
wallace - September 18, 2017
Tool Type
MultiTool
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Star bit and tweezers
1. Disassembled unit
2. Wire power cord to new switch assembly
3. Attached brush holders to field
4. Attached field to switch
5. Routed wires to specific points so unit will close and run
6. Place all button and lock knobs in place.
7. Reassembled unit
(Pay Close Attention To Where The Wires Are Routed, if they are not just right the outer casing will not close cleanly and the motor will not run)
2. Wire power cord to new switch assembly
3. Attached brush holders to field
4. Attached field to switch
5. Routed wires to specific points so unit will close and run
6. Place all button and lock knobs in place.
7. Reassembled unit
(Pay Close Attention To Where The Wires Are Routed, if they are not just right the outer casing will not close cleanly and the motor will not run)
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
