866-322-9842
Mon-Fri 7am-1am EST
Sat-Sun 7am-11pm EST
Repair Parts Home  Lawn Equipment Parts  Briggs and Stratton Parts  205858GS Voltage Regulator‎

Voltage Regulator‎

Part Number: 205858GS
Snapper
Availability: 25+ in stock
Price: $79.63
Quantity:
Order within the next 9 hours
and your part ships today!

*This part replaces obsolete part #: 202165GS, 195011GS, 200962GS, 189769GS and 198339GS.

Description:
This authentic replacement part is specially designed for Briggs and Stratton generators. It is supplied from the original equipment manufacturer. This is an important component of the unit which regulates the voltage. Over time it may develop electrical or mechanical issues eventually requiring a replacement. This high-quality component is sold as an individual item. Make sure to refer to the owners manual and the diagrams of your model for the exact location and the correct application of this regulator. You will need a screwdriver and a wrench set to remove the housing in order to perform this repair.
Product Information
Manufacturer: Briggs and Stratton, Snapper
Product Number: 205858GS
Classification: Part
Weight: 0.20 lbs.
Shipping: Ships Worldwide
Compatibility

This part is compatible with the following machines:

Briggs and Stratton
Snapper

Products Compatibility

This item works with the following types of products:

  • • Generator
Repair Instructions: Submitted by Customers Like You
12 of 14 people found this instruction helpful
Tool Type:
Generator
Parts Used:
Voltage Regulator‎ - 205858GS
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Socket set
No power produced
Remove rear of generator by unscrewing four nuts, remove cover, remover controller, remove wires and reconnect to new controller once completed wrap wires around board as you found on the old board. Refit and replace covers. Have all the power I need now. Thank you.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
8 of 9 people found this instruction helpful
Tool Type:
Generator
Parts Used:
Voltage Regulator‎ - 205858GS
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Pliers, Socket set, Nutdriver
No power output on customer's John Deere 6200 portable generator
1. Check for power output at receptacles (No go)
2. R&R end cover & generator end plate. Clean slip rings on rotor. Check brushes for proper contact.
3. Check for min. AC output from rotor and stator while running. (OK)
4. Replace AVR. Check for generator output. (No go)
5. Disconnect + and - leads from brush block. Start generator and flash rotor with 12vdc.
6. Re-connect brush leads and re-start. Check for output. (OK!)

NOTE: On this type of AVR *always* make sure all leads go to the proper terminals. The AC voltage sense and AC input to the AVR are different size terminals, but it is still possible to get the individual leads mixed up and the generator won't put out at governed speed. Be sure to follow the instruction sheet exactly on the positions of the voltage sense & AC input wires to the AVR! (The wires have numbers printed on the insulation)
Did you find this story helpful?
Thanks for voting and helping fellow customers!
5 of 6 people found this instruction helpful
Tool Type:
Generator
Parts Used:
Voltage Regulator‎ - 205858GS
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Nutdriver, Lever for controlling height of generator relative to frame
Generator failed to output power
1. Unbolted wired end of generator end housing from frame.
2. Removed four long screws holding the end housing to the rest of the generator assembly
3. Used lever to raise the generator housing (and generator up to clear the frame).
4. Removed housing from the stator/rotor assembly
5. Followed the attached instruction sheet for the voltage regulator
5a. Discarding the "booster" previously undefined by the manufacturer. Part of the sheet instructions.
6. Reassembled in the reverse order.
7. Tested = OK
Did you find this story helpful?
Thanks for voting and helping fellow customers!
4 of 4 people found this instruction helpful
Tool Type:
Generator
Parts Used:
Assy, Holder, Brush - 66386GS
Voltage Regulator‎ - 205858GS
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Nutdriver
Generator did not put out 120 volts
I took cover of generator off replaced the avr and the brushes and put everything back on started the generator up and checked it ready to go
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 3 people found this instruction helpful
Tool Type:
Generator
Parts Used:
Voltage Regulator‎ - 205858GS
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Nutdriver
No voltage output
Remove end cover on generator.
Unplug old PC board
Plug in new PC board
Slide PC board into locator slots
Reinstall end cover
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Generator
Parts Used:
Assy, Holder, Brush - 66386GS
Voltage Regulator‎ - 205858GS
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Pliers
No power
Replaced the old parts with the new ones followed instructions that came with the parts . All went well generator now puts out electricity problem fixed. Advice take photo of wiring so everything go's back the same way. Reair was very easy.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 4 people found this instruction helpful
Tool Type:
Generator
Parts Used:
Voltage Regulator‎ - 205858GS
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Socket set, Voltmeter
No voltage output
1 Removed generator end cover.
2 Transfer wires one at a time to new AVR.
3 Slide AVR in slot.
4 Remove old brush leads .
5 Add new brush leads.
6 Put cover back on,
7 Test for voltage..
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Generator
Parts Used:
Assy, Holder, Brush - 66386GS
Voltage Regulator‎ - 205858GS
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Socket set, Small alligator clip jumper cables
No output from generator
1. Removed generator cap using 8mm socket set
2. Removed and replaced old AVR and brush assembly
3. Followed included instructions to remagnetize brush assembly by using small alligator 4. Clip jumper cables (not included) to connect positive and negative leads of brushes to a positive and negative posts of a 12 V battery (not included).
5. Started and ran the generator for a few seconds.
6. Removed jumper cables.
7. Reconnected lead wires.
8. Re-installed the cap.
9. Started generator and now works as good as new!

Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Generator
Parts Used:
Assy, Holder, Brush - 66386GS
Voltage Regulator‎ - 205858GS
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Generator put out no power when running
1. Remove plastic cap/vent off the end of generator
2. Remove and replace brush assembly, being sure to connect wires correctly
3. Remove the old voltage regulator and booster (if equipped), replacing both items with the voltage regulator as described in the directions included with the new voltage regulator
4. Start generator and retest for proper function (electrical output)
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Generator
Parts Used:
Voltage Regulator‎ - 205858GS
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Nutdriver
Generator wouldn't produce power
It took & 5 minutes to replace the part
I took the back cover off the generator, slid the old regulator out unplugged it, slid the new one in, plugged it up, put the cover back on, works good,
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Discussion
Discussion for Voltage Regulator‎ - ( 205858GS )
Discussion is closed. To ask our experts a question about a part, use the Q&A feature.
Question: AVR Regulator Control

leecarrol

what should the input and output voltage for the regulator be?
Question: Color Wires

army75ranger

on the avr the wire diagram two colors red blue on left side of avr is it at top red an under it red and on rite side of avr top blue and lower red. let me know . and thank you
Question: AVR Typical Failure Mode?

bobright

VXG6500 (model 030340-0) The output goes to zero after a short time. If the AVR output that connects to the brushes goes to zero, will the AC output of generator also go to zero? I have not yet simulated the AVR output to the brushes yet.
Question: In Correct Voltage Out Put

funddy

can the output voltage be adjusted
visa mastercard discover american express PayPal
HACKER SAFE certified sites prevent over 99.9% of hacker crime.

fancyboxy