Easy
Less than 15 minutes
This is an authentic Generac replacement part that is OEM sourced to ensure a high level of quality. The valve is intended to be used with portable generators. This part is part of the fuel system and is used to regulate the flow of fuel to the engine. This item is sold individually.
Valve, Fuel Shutoff 0H0406
OEM part for: Generac
Part Number: 0H0406
$14.01
Usually ships in 7 - 12 business days
Leaves our warehouse within 7 - 12 business days
Compatibility
This part will fit the following 4 machines
Generac
05789-0 (GP3250) Portable Generator View Diagrams & Manuals
0057890 (5581121 - 9646014D)(2016) Gp3250w 208 Carb -05-09 Generator View Diagrams & Manuals
0057890 (5581122 - 6932040D)(2012) Gp3250w 208 Carb -02-10 Generator View Diagrams & Manuals
0057890 (7118013D - 7945934D)(2013) Gp3250w 208 Carb -02-22 Generator View Diagrams & Manuals
This item works with the following types of products:
- Generator Parts
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Valve, Fuel Shutoff
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Generator had been damaged in storage
Nolan - January 4, 2016
👍 6 of 6 people found this instruction helpful
Tool Type
Generator
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Nutdriver, air compressor (optional)
The petcock to turn gas on and off had been damaged and was leaking, so gas had been shut off. The air cleaner had also been bumped and would not seal well so I changed it as well. Tipped the generator on end to avoid gas leakage. Pulled 3 bolts out of air cleaner and removed the old one, while I had it apart, pulled the carb off and blew out the jets. Replaced the carb and put new air cleaner on. Removed the gas lines from petcock and unscrewed it from tank, screwed the new one in its place and replaced the hoses. Set the generator back down and pulled the rope a couple times and off it went.
Quick and simple!
Quick and simple!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Old fuel valve.
Joe - September 14, 2017
👍 1 of 1 people found this instruction helpful
Tool Type
Generator
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Pliers, Adjustable Wrench
Parts Used
Removed the old valve and replaced it with the new one.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
No fuel passage on shutoff valve
Israel - March 26, 2017
👍 1 of 1 people found this instruction helpful
Tool Type
Generator
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Adjustable Wrench
Parts Used
Removed the fuel from the tank
Removed the fuel line from the old shutoff
Remove the old shutoff
Installed the new one
Installed the fuel line
Removed the fuel line from the old shutoff
Remove the old shutoff
Installed the new one
Installed the fuel line
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Two generators, replaced AVR on old Generac and oil sensor on Troy Bilt. Troy took 5 minutes and Generac took about 10 minutes.
Michael - November 28, 2019
Tool Type
Generator
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Pliers, Socket set, Nutdriver, My two hands
Generac, removed the cover off generator and replaced AVR. Then installed fuel valve. I stole the fuel valve the year before for my dune buggy and had to replace it. The Troy Bilt needed the oil sensor because it kept shutting off. I bypassed while waiting for the part. Installed it in less than 5 minutes. The Generac took about 10 minutes for the repair parts. I took an additional 30 minutes to clean up the carb on the Generac. It was gummed up. Done.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Flat blade on shut off valve broke off.
Paul - May 30, 2017
Tool Type
Generator
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Wrench Set
Parts Used
Had to purchase gasoline tolerant rubber fuel line from auto parts store. Put generator on blocks to have valve higher than fuel level in tank. Removed old shut off valve. assembled new shut off valve from box, had to insert filter into valve assembly. Removed old fuel line and installed new onto carburetor and shut off valve. Insert valve assembly into opening on bottom of fuel tank and tighten with wrench. Test for leaks first and then test run generator. Whole job took less than 15 minutes.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Old fuel shut off toggle switch fell off
Stan - August 24, 2016
Tool Type
Generator
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Pliers, Wrench Set
Parts Used
I got the proper tools required ( two wrenches and pliers ) I then placed three bricks under the generator to force the gas in the tank towards the back so there would be no leakage when removing old part. I attached lower gas line to replacement part. I loosed top bolt and removed old part and put replacement part in place and tightened it up. It works great!!!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Generator would not start.
Gerald - July 9, 2017
👍 0 of 1 people found this instruction helpful
Tool Type
Generator
Difficulty
Medium
Time
15-30 minutes
Tools Used
Wrench Set
Parts Used
1. No gas coming from tank
2. Replaced the valve and the filter.
3. Generator started right up.
2. Replaced the valve and the filter.
3. Generator started right up.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
