Spiral Crescent [735-04032] for Lawn Equipments

Description:

This is a Genuine OEM Approved replacement part designed for use with Snow Throwers. This part is made out of Rubber and it is Sold Individually. This part mounts with 2 Screws (Sold Separately) at each end.

You would need a Wrench to replace this part

• Remove the ignition key
• Disconnect spark plug
• Tilt Snowblower back so it rests on it’s handles for support
• Remove all 4 bolts on the auger paddle and then remove the paddle
• Install the new auger paddle into the bracket on the auger shaft
• Make sure that the auger paddles are secure

Frequently Purchased With

Rubber Paddle..
$7.15

Auger Assembly..
$158.55

Compatibility

This part is compatible with the following machines:

MTD

Yard Machines

31AM2N1B700 (2008) Snowblower

Bolens

31AE160-163 (2004) Snowblower

Yard Man

31A-2B5-801 (2005-2) Snowblower
31AS295-801 (2005-2) Snowblower
31AS2B5-801 (2005-2) Snowblower

31AS295-801 (2006) Snowblower
31AS2B5-801 (2006) Snowblower
31AS2B5-801 (2007) Snowblower

Expand the 150+ compatible machines

Products Compatibility

This item works with the following types of products:

• Snowblower

Repair Instructions: Submitted by Customers Like You

1 of 1 people found this instruction helpful

Tool Type:

Snowblower

Parts Used:

Rubber Paddle - 735-04033

Spiral Crescent - 735-04032

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Power Drill

Paddles just wore out.

Removed the old paddles and installed the new ones. Machine works as good as when it was new.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Rubber Paddle - 735-04033

Spiral Crescent - 735-04032

Repair Difficulty:

Easy

Time Spent Repairing:

30-60 minutes

Tools Used:

Socket set

4 Rubber spiral crescents and 2 rubber paddles were worn out.

Very easy to replace the rubber parts on my Troy-Bilt snowthrower. All were exactly the same as the worn out ones so I am extremely satisfied.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Spiral Crescent - 735-04032

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Wrench Set

rubber paddles worn out

They are held on by simple hex-headed screws. Took less than half an hour to replace all 4 and adjust the bottom plastic scraper.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Spiral Crescent - 735-04032

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Socket set

The rubber crescents were wearing down so not getting a clean snow throw.

Removed four worn crescents from auger and replaced with new. Small snowblower easy replacement. Rubber crescents, pretty simple fix.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Spiral Crescent - 735-04032

Repair Difficulty:

Easy

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers, Adjustable Wrench

Paddles were worn out

Removed old paddles and replaced these with new paddles

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Spiral Crescent - 735-04032

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

, Air ratchet

Rubbers were worn out.

Removed all the rubbers. Replaced all rubbers ,piece of cake.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Spiral Crescent - 735-04032

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Socket set

Just needed new pedals for snowblower.

Just took the sockets out and replaced the pedals. Very easy job!

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Spiral Crescent - 735-04032

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Socket set

Needed new paddles for the snow blower.

Took the old ones off and replaced them with the new ones from eReplacement. Everything came off smoothly and the new paddles fit perfectly.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Spiral Crescent - 735-04032

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Socket set, Vice grip

rubber blades on auger worn out

I Removed the old blades in advance of arrival of the new ones as the machine was useless anyway.
when the blades arrived I used the old bolts to reattach the new blades clipping the new blades in place with the vice grip while I aligned the holes. On my machine there is a small rubber blade that fills the gap between the right and left Rubber augers. I failed to order this but Just turned the old ones backward and forced them down to match the left and right and re tightened them. It's probably best to order the new replacement.
That's about all there is to it. I used the machine today on a 5" snow fall and it seemed to perform well.. Note:: you might have to replace the bar on the bottom of the machine that actually contacts the surface that you're plowing, I did that a couple of years ago

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Spiral Crescent - 735-04032

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Socket set

Rubber Blades worn out on snowblower

Took each piece off Individually, And replaced each Individually, My way of making sure parts went on same way they came off

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Reviews

Average Rating (out of 5):

4 Reviews

Click to filter by ratings:

5 stars

4

4 stars

0

3 stars

0

2 stars

0

1 stars

0

Sort by:

Highest Rating
Most Recent

< PREV

1

NEXT >

Perfect Match

After receiving the wrong part from a different supplier, I was a little shy of trying again with a new supplier but Ereplacement was right on the money. It was an easy order. My only problem was with the shipping company. They kept changing the delivery date. Final was a day late. About 36 hours after they said it was on the truck and out for delivery from about 5 miles away.

Guest - August 27, 2022 Verified Purchase

Easy repair, thank you.

Paddles received...now found out the cause of old ones coming apart. Weld on the rod holding paddles broken causing damage to paddles. Will now have to order whole assembly. Thanks

Guest - February 3, 2022 Verified Purchase

Great delivery

Parts were delivered quickly and fit correctly. Yet to try in the snow but I'm sure I will have an opportunity and sure the snowblower will work much better

Guest - November 13, 2020 Verified Purchase

The review says it all.

The product was received promptly,for perfectly,and is good quality.I am very satisfied. Thanks.

Guest - October 14, 2019 Verified Purchase

Verified Purchase

eReplacementParts Team

Sort by:

Highest Rating
Most Recent

< PREV

1

NEXT >