866-322-9842
Mon-Fri 7am-1am EST
Sat-Sun 7am-11pm EST
Repair Parts Home  Power Tool Parts  DeWALT Parts  151284-00SV Sander Pad and Backing Plate

Sander Pad and Backing Plate

Part Number: 151284-00SV
DeWALTBlack and DeckerPorter Cable
Availability: 25+ in stock
Price: $24.05
Quantity:
Ships within 1 business day

*This part replaces obsolete part #: and 151284-00.

Specifications
  • O.E.M. Dewalt sander pad
  • For use with clamp-on sandpaper
  • Includes metal backing plate and padded sanding surface
Description:
This sander pad is a genuine Dewalt replacement part, not generic or aftermarket. It it a Foam Rubber type pad and is compatible with clamp-on style sandpaper. It is not compatible with hook-and loop sandpaper. This sander pad has a metal backing plate with a padded sanding surface attached. The pad is complete and ready to install.

This sander pad will fit the Dewalt sanders listed in the 'Compatibility' section below. It is not guaranteed to fit any other power tool models.
Product Information
Manufacturer: DeWALT, Black and Decker, Porter Cable
Product Number: 151284-00SV
Classification: Part
Weight: 0.07 lbs.
Also Known As: Sander Cushion, Backing Pad, Conversion Pad, Sanding Shoe, Base Plate
Shipping: Ships Worldwide
Repair Guides
Watch the Repair Video for Sander Pad and Backing Plate
How to Replace the Sander Pad on a DeWALT Sander
Articles:
How to Replace the Sander Pad on a DeWALT Sander
Step-by-step instructions for removing and installing the sander pad on your DeWALT sander....
October 04, 2017
Products Compatibility

This item works with the following types of products:

  • • Sander
Questions & Answers

No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
37 of 38 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Sander Pad and Backing Plate - 151284-00SV
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Sander pad worn.
Replacing a worn pad on a palm sander is an easy task. First turn the sander upside down and locate the four screws that secure the pad to the plate. These may be torx bit screws so beware of that. Remove the 4 screws and remove the rubber sanding pad from the sander. Clean the plate of any residual saw dust and dirt. This can be accomplished by blowing with compressed air and/or a rag soaked in a little mineral spirits. Next, put the new pad in place aligning the holes and replace the 4 screws. Your pad sander is ready to go. I have 2 DeWalt 1/4 sheet pad sanders that I use very hard and these pads wear down over time. Suggestion, some sandpapers have an adhesive on the back that can stick to and sometimes tear the sander pad. I know this from personal experience. Spraying a little WD-40 on the pad prior to putting sandpaper on will help prevent any sticking of the sandpaper when it's time to change it out. Good luck.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
11 of 11 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Sander Pad and Backing Plate - 151284-00SV
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Nutdriver
Worn base plate for a DeWalt orbital sander
Remove 4 screws that hold on the base plate... install new base plate and tighten screws using a star-bit driver. Be sure that the screws are secured tightly, as they will tend to loosen up during use of the sander.

Thanks for the parts and terrific service. I enjoy using e-replacement parts.

Dr. Jones
Did you find this story helpful?
Thanks for voting and helping fellow customers!
6 of 6 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Sander Pad and Backing Plate - 151284-00SV
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Remove/Replace Worn Pad
VERY Simple
1. Remove 4 screws
2. Remove old pad
3. Place new pad
4. replace 4 screws
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 3 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Sander Pad and Backing Plate - 151284-00SV
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Pad worn out
Remove four screws from old pad, Remove old pad. Place new pad on sander and use the four screws to attach to the sander.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Sander Pad and Backing Plate - 151284-00SV
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
No problem
Remove the four screws from the old pad, and remove the old pad. Place the new pad on the sander and attach it with the four screws.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Parts Used:
Platen - N073798
Sander Pad and Backing Plate - 151284-00SV
Seal,Dust - 144974-00
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Pliers, Power Drill
A piece of the platen broke causing the vibration of the sanding pad to stop.
1. Removed the worn down sanding pad and broken platen.
2. I noticed that one of the brass screw holes that I screw the platen to the sander base had become loose. This was the most time consuming part of my repair to fix (and probably would never happen to anyone else).
3. After reassembling most of the sander back together, I added the dust seal to the platen, screwed the platen and the pad back to the sander.
4. Problem solved; it runs like a champ.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Parts Used:
Sander Pad and Backing Plate - 151284-00SV
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Pad worn out
Remove 4 screws, remove the old pad
Install the new pad with the screws
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Parts Used:
Platen - N073798
Sander Pad and Backing Plate - 151284-00SV
Seal,Dust - 144974-00
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Dust seal failed causing build up of dust that caused the breaking of the platen and plate.
Removed the 4 screws on the bottom of the platen and sanding plate that hold them to sander and then replace with new parts and tightened screws.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Parts Used:
Sander Pad and Backing Plate - 151284-00SV
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Backing pad was worn out
Took out screws took off old pad put on new pad screwed in the screws all is well
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Parts Used:
Sander Pad and Backing Plate - 151284-00SV
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Rubber pad worn out
Remove four screws then the old pad, install the new pad with the four screws, very easy.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Discussion
Discussion for Sander Pad and Backing Plate - ( 151284-00SV )
Discussion is closed. To ask our experts a question about a part, use the Q&A feature.
Question: D26441 Hook And Loop Pad

1371067

Is a hook and loop pad available for the model D26441 sander?
WJA
Hello 1371067,

I have been searching for a Hook and Loop pad to sub for the 151284-00SV Sander Pad & Backing Plate (Rubber Foam), but I haven't been able to locate one. Maybe one of our forum members may know of something that will work and let us know.

-WJA
Question: Rubber Pad

jconnerpa

I need to replace the rubber pad on model D26441. The backing plate is good and does not need replacing. I cannot find just a rubber pad on the parts list. Can you help with this?
WJA
Hello jconnerpa,

The only way to get a new rubber pad is by ordering part number, 151284-00SV. The factory doesn't provide it any other way.

-WJA
Reviews
4.2
Average Rating (out of 5):
5 Reviews
Click to filter by ratings:
5 stars
3
4 stars
1
3 stars
0
2 stars
1
1 stars
0
  • Highest Rating
  • Most Recent
< PREV
  • 1
NEXT >
  • good stuff
    Just like my previous experience with ereplacement,,,,,great service, a very speedy delivery, easy replacement instructions and a part that fit and was just like factory new after the installation. I am glad to know about ereplacement.com and will continue to do business with them.
    Guest - 10 days ago Verified Purchase
    Just like new again
    Works like it should again. Should of bought this replacement the first time instead of a cheap knockoff.
    Guest - 11 days ago Verified Purchase
    Works good as new
    Easy to replace, Works good as new!
    Guest - April 20, 2019 Verified Purchase
    Easy repair, just took a few minutes
    The part arrived quickly, replacement was very easy. Was just the part my sander needed for smoother finishes.
    Guest - April 22, 2019 Verified Purchase
    Right pad, wrong backing
    Although the part itself is half the cost of the machine, it still wasn't the right one for the model I have. I was able to modify the base by drilling new mounting holes in the backing plate and making it work. I was unable to find backing plates that fit the DeWalt 6511k model. This model was not listed as being compatible with the part I purchased, but I thought I would give it a try anyway.
    Guest - 21 days ago Verified Purchase
    eReplacementParts Team
    Verified Purchase
    eReplacementParts Team
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    NEXT >
    visa mastercard discover american express PayPal
    HACKER SAFE certified sites prevent over 99.9% of hacker crime.

    fancyboxy