This is a genuine replacement part sourced from the original manufacturer for use with outdoor power equipment. The special needle bearing is commonly used to reduce friction between a rotating shaft and fixed part assembly. This needle bearing is available as an individual replacement part.
Replaced needle bearings, drive chain and the input shaft. it was pretty much a straight forward disassembly of the entire rototiller. With the exception of the removal of the left hand side tines and drive wheel. It required using the two arm puller for removal of these items. the only issue I had with reassembly was the rear tine axle
... Read moreseals. they had a pretty tight tolerance, and I had to heat them up to expand them to fit on the hubs. As far as special instructions, I would recommend not removing the three shaft nuts on the left hand side of the transmission during disassembly and splitting of the transmission body. It\'s not needed, and the re-tightening of these nuts can be a little tricky as far as over tightening them. You should turn the Tine axle during re-tightening to make sure all of the gear works is turning smoothly before you move to reassembly of the rest of the tiller. Nothing worse than taking it back apart to loosen something.
Read less
Did you find this story helpful?
Thank you for voting!
Tines would not engage
Larry from Licking, Missouri
2 of 3 peoplefound this instruction helpful.
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
1. Took entire tiller apart .
2. Removed motor.
3. Tore down transmission .
4. Checked condition of all parts .
5. Cleaned all good parts .
6. Ordered parts needed.
7. Received parts .
8. Put transmission back together .
9. Put tiller back together.
10. TAKE LOTS OF PICTURES AS YOU T
... Read moreAKE THE TILLER APART . THIS WILL BE VERY HELPFUL .
11. Used over a gallon of marine grease .
12 . Make sure the transmission moves in every gear before reassembling tiller .
13. Replace ALL bearings .
Read less
Did you find this story helpful?
Thank you for voting!
A Chain broke on the wheel drive in the gear box of a Charftman rear tine tiller .
1 Took the tiller all apart
2. Split the gear box in half
3 . took out all the gears and sifter
cleaned out old grease .
4 replaced nidle bearings .
5 out new chain on .
6 replaced all the Grears for tines and wheels .
7 replace gasket .
8 bolted gearbox back to gether and put
... Read more fream back on gearbox .
9 Ran it and its all working . Tilles and wheels pull as it all should . On A Craftman REAR tine Tiller .
Completely disassemble tiller main case
Remove all grease,if it is brown it had water in it.this case are a two piece shell type.
Replace the shiftier rod,spring bearing,water gets inside where the spring and ball are. Mine got water inside from using the pressure washer to clean.
Use 400 grit sandpaper to polish any rus
... Read morety shafts.
Re-lube chain and gears using good grease,Valvoline #2 red grease works good.
Make sure to work grease into the needle bearings real good ,as they don\'t get any grease otherwise it\'s the way they designed them.
Clean off the mating surface of the two halves with acetone or lacquer thinner.
Use a bead of automotive silicon seal without a gasket to seal.put a bead inline with the bolt holes and at the holes go all the way around the hole.
Carefully put the shell half back on taking care not to forget any parts ,tighten as needed .
Let sealer set up 24 hours before using.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP9285518
Manufacturer Part Number: 532006803
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_7.gif "Part Location Diagram of 532006803 Husqvarna Trimmer Needle Bearing")
_WW_7.gif "Part Location Diagram of 532006803 Husqvarna Trimmer Needle Bearing")
