This is a genuine manufacturer-sourced replacement component which is specially designed for use with lawn and garden equipment. It is one of the parts that helps to provide a tight seal for the shaft, please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this durable item is made of high-quality metal with rubber and is sold individually.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
nice, well-made axle seals
These seals were high quality--perhaps old stock? They were a tad too small for my application but I was able to make them work, since my machine is about 60 years old, parts are no longer made. The service was fast and efficient.
Guest - November 12, 2022
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
Be the first to ask our experts a question about this part!
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Replaced needle bearings, drive chain and the input shaft. it was pretty much a straight forward disassembly of the entire rototiller. With the exception of the removal of the left hand side tines and drive wheel. It required using the two arm puller for removal of these items. the only issue I had with reassembly was the rear tine axle
... Read moreseals. they had a pretty tight tolerance, and I had to heat them up to expand them to fit on the hubs. As far as special instructions, I would recommend not removing the three shaft nuts on the left hand side of the transmission during disassembly and splitting of the transmission body. It\'s not needed, and the re-tightening of these nuts can be a little tricky as far as over tightening them. You should turn the Tine axle during re-tightening to make sure all of the gear works is turning smoothly before you move to reassembly of the rest of the tiller. Nothing worse than taking it back apart to loosen something.
Read less
Did you find this story helpful?
Thank you for voting!
A Chain broke on the wheel drive in the gear box of a Charftman rear tine tiller .
1 Took the tiller all apart
2. Split the gear box in half
3 . took out all the gears and sifter
cleaned out old grease .
4 replaced nidle bearings .
5 out new chain on .
6 replaced all the Grears for tines and wheels .
7 replace gasket .
8 bolted gearbox back to gether and put
... Read more fream back on gearbox .
9 Ran it and its all working . Tilles and wheels pull as it all should . On A Craftman REAR tine Tiller .
Completely disassemble tiller main case
Remove all grease,if it is brown it had water in it.this case are a two piece shell type.
Replace the shiftier rod,spring bearing,water gets inside where the spring and ball are. Mine got water inside from using the pressure washer to clean.
Use 400 grit sandpaper to polish any rus
... Read morety shafts.
Re-lube chain and gears using good grease,Valvoline #2 red grease works good.
Make sure to work grease into the needle bearings real good ,as they don\'t get any grease otherwise it\'s the way they designed them.
Clean off the mating surface of the two halves with acetone or lacquer thinner.
Use a bead of automotive silicon seal without a gasket to seal.put a bead inline with the bolt holes and at the holes go all the way around the hole.
Carefully put the shell half back on taking care not to forget any parts ,tighten as needed .
Let sealer set up 24 hours before using.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP9017744
Manufacturer Part Number: 532155236
Tiller
- Husqvarna Tiller Model 96093002501/2014-03 (96093002501/201403, 96093002501/2014 03) Parts
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Seal or Gasket","title":"Seal or Gasket","url":"/parts/lawn-and-garden/tiller/seals-and-gaskets/"},{"position":2,"name":"532155236","title":"532155236","url":""}]
_WW_7.gif "Part Location Diagram of 532155236 Husqvarna Seal Asm, Oil")
_WW_7.gif "Part Location Diagram of 532155236 Husqvarna Seal Asm, Oil")
