Easy
15-30 minutes
This is an OEM sourced replacement part used on Shindaiwa trimmers. Its purpose is to filter out dust and debris from contaminating the carburetor and engine. When replacing the filter you can open the package in comes in and put a bit of two cycle oil in the bag and let it absorb into the filter. Then remove it from the bag and squeeze it with a paper towel to remove the excess oil.
To replace this filter no special tools are needed. Simply remove the cover and replace the filter element.
Foam Air Filter A226000740
OEM part for: Shindaiwa
Part Number: A226000740
$3.99
In Stock
Ships within 1 business day 
Jump To:
Product Description ?
- Classification: Part
- Weight: 0.01 lbs.
- Shipping: Ships Worldwide
Frequently Purchased Together ?
Compatibility
This part will fit the following 30 machines
Shindaiwa
AH230 Articulated Hedge Trimmer View Diagrams & Manuals
AH231 Articulated Hedge Trimmer View Diagrams & Manuals
LE230 Lawn Edger View Diagrams & Manuals
LE231 Lawn Edger View Diagrams & Manuals
P230 Pole Pruner View Diagrams & Manuals
P231 Pole Pruner View Diagrams & Manuals
PB230 Power Broom View Diagrams & Manuals
C230 Brushcutter View Diagrams & Manuals
80280 Multipurpose Tool Carrier View Diagrams & Manuals
80192 Multipurpose Tool Carrier View Diagrams & Manuals
TCX230 Trimmer View Diagrams & Manuals
X230 Trimmer View Diagrams & Manuals
T231 Trimmer View Diagrams & Manuals
T231B Trimmer View Diagrams & Manuals
T231X Trimmer View Diagrams & Manuals
T231XB Trimmer View Diagrams & Manuals
M230 Multipurpose Tool View Diagrams & Manuals
M231 Multipurpose Tool View Diagrams & Manuals
T-250 Trimmer View Diagrams & Manuals
C-250 Brushcutter View Diagrams & Manuals
LE250 Lawn Edger View Diagrams & Manuals
T230XR-EMC (36005665-36007144) Gas Trimmer View Diagrams & Manuals
T230XR-EMC (9013195-9095664) Gas Trimmer View Diagrams & Manuals
T230 Trimmer View Diagrams & Manuals
C230 (36005611-36009050) Brushcutters (C) View Diagrams & Manuals
C230 (9010691-9095610) Brushcutters (C) View Diagrams & Manuals
C230 (T23420001001-T23420999999) Brushcutters (C) View Diagrams & Manuals
C230 (AR)(C29626001001-C29626999999) Brushcutters (C)Ar View Diagrams & Manuals
C230PT (T12220001001-T12220999999) Brushcutters (C) View Diagrams & Manuals
T231 (T231B) Grass Trimmers (T) View Diagrams & Manuals
Show More Compatible Models
This item works with the following types of products:
- Hedge Trimmer Parts
- Trimmer Parts
- Edger Parts
- Pruner Parts
- Multi-Tool Parts
This part replaces obsolete part #: 20018-81750
Repair Videos ?
Articles:
|
Filthy Filters? This article will show you how to install a filter kit on an Echo SRM-225 trimmer....
May 27, 2015
|
Customer Part Reviews ?
Average Rating (out of 5):
Click to filter by ratings:
5 stars
3
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
Perfect fit.
This fit perfectly with the new housing that was also an upgrade and perfect fit
Guest -
August 24, 2023
Verified Purchase
Fast easy and the parts were correct
Fast easy and the parts were correct
Guest -
April 10, 2023
Verified Purchase
.
Part was exactly what I needed. Great service.
Guest -
April 7, 2021
Verified Purchase
t
t
t -
t days ago
Verified Purchase
eReplacementParts Team
t
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Foam Air Filter
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
It was 12 years old and wouldn't restart once it was warmed up after use.
Lesley - July 28, 2016
👍 1 of 1 people found this instruction helpful
Tool Type
Trimmer
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Pliers
Unscrewed the old carburetor and removed the gas lines. Installed the new carburetor and the gas lines, as well as the air filter.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Lost air filter
Joe - February 12, 2024
Tool Type
Trimmer
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
, nothing
Replaced air filter and cover
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Used my Alen wrench and took it apart and re assembled same way. Made sure everything was nice and snug.
leshune - November 5, 2021
Tool Type
Trimmer
Difficulty
Easy
Time
15-30 minutes
Tools Used
, Alen wrench
Removed pull rope replaced it and replaced some older parts. New parts worked like a champ she sounds amazing. Basically removed bolts holding it and replaced it
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Extremely hard starting
Cris - June 30, 2020
Tool Type
Trimmer
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver, rag and carb cleaner
Unscrewed the two screws on inside of air cleaner. Removed carb. removed old gasket cleaned area and replaced with new one. Fixed the problem.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Clutch wore out and fuel leak, general maintenance.
Tarael - February 12, 2019
Tool Type
Trimmer
Difficulty
Medium
Time
1-2 hours
Tools Used
Screwdriver, Wrench Set, Metric Allen wrench set, parts cleaner, compressed air
Removed the shaft from the engine, air filter, plug cover and clutch shroud, fuel tank and cleaned all the parts. Replaced cracked fuel lines and pipe assy, with fuel filter and breather. Replaced clutch and spark plug. Checked air gap at mag/coil and lubed shaft end splines and greased the head.
Keeping the cooling fins clean after each use is important to prevent overheating.
Keeping the cooling fins clean after each use is important to prevent overheating.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
The engine was getting flooded the spark plug would be soaked with fuel .
Johnny - August 23, 2018
Tool Type
Trimmer
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver
I removed the carburetor the two screws behind the air filter and two fuel lines also tilt the carb to disconnect the throttle cable .Put the fuel lines back in same location when you reassemble.I disassembled the carb the four screws that holds the prime bulb and discovered the fuel pump diaphragm was hard and brittle. The diaphragm was holding the needle open causing the engine to flood. I reassembled the carburetor installing a new Gasket/ Diaphragm Kit. The trimmer runs Great !
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Fuel line separated inside the fuel tank
Dennis - September 22, 2017
Tool Type
Trimmer
Difficulty
Easy
Time
30-60 minutes
Tools Used
Screwdriver, Pliers
Removed fuel tank. replaced fuel line and fuel filter. Replaced both air filters
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Cracked primer bulb,needed a new air filter
Joe - August 5, 2017
Tool Type
Trimmer
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
Removed the screws form the primer cover and removed the cracked primer, and installed the new one. Screwed the primer cover down. Removed the air filter cover and removed the old filter and placed the new one in, then replaced the cover
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Air Cleaner broken
Bruce - May 18, 2017
Tool Type
Trimmer
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
1. Removed the carburetor air cleaner screws.
2. Installed the new air cleaner housing and the air cleaner.
2. Installed the new air cleaner housing and the air cleaner.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Maintenance on my trimmer and blower
Stephen - May 17, 2017
Tool Type
Trimmer
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Wire with a hook
Use a length of wire with a hook bent at the end of it. Remove the gas cap, and use the hook to fish out the fuel line and filter. Remove the old filter, and install the new one, return the filter and fuel line back into the tank. And replace the cap.
Remove the air filter cover and remove the old filter and install the new one, replace the cover
Remove the air filter cover and remove the old filter and install the new one, replace the cover
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Load More Install Stories
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
