Medium
15-30 minutes
This is a genuine part which is supplied directly from the original equipment manufacturer and is used with Jet Drill Presses. When you order this kit you will received figure numbers 6-18 ( Table Bracket, Gear, Gear Shaft, Worm Pinion, Crank Handle, Table Bracket, Cap Screw, Angle Scale, Centering Scale, and the Drive Screw.) For installation, you will need a screwdriver and a wrench to aid you.
Table Bracket Assembly JDP15-1006
OEM part for: Jet
Part Number: JDP15-1006
$286.92
Usually ships in 7 - 12 business days
Leaves our warehouse within 7 - 12 business days
Product Description ?
- Larger ID 2-3/4"
- Smaller ID 1-7/8"
- Classification: Part
- Weight: 11.35 lbs.
- Shipping: Ships Worldwide
Compatibility
This part will fit the following 8 machines
Jet
J-2500 (354400) Drill Press View Diagrams & Manuals
J-2530 (354401) Drill Press View Diagrams & Manuals
JDP-15M (354165) Drill Press View Diagrams & Manuals
JDP-15MF (354166) Drill Press View Diagrams & Manuals
354165 15 Inch Bench Mount View Diagrams & Manuals
354166 15 Inch Floor Mount View Diagrams & Manuals
354400 115v Floor Model View Diagrams & Manuals
354401 1 Ph 115v Bench Model View Diagrams & Manuals
Show More Compatible Models
This item works with the following types of products:
- Drill Parts
- Drill Press Parts
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Table Bracket Assembly
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Broken bracket
Robert - February 21, 2016
👍 1 of 1 people found this instruction helpful
Tool Type
Drill Press
Difficulty
Easy
Time
15-30 minutes
Tools Used
, hex hd wrench
Parts Used
Remove the set screw on the top collar, then carefully slide the table bracket from the column.
align the rack and pinion gears, then position the new bracket on the column. replace the top collar ring and tighten the set screw, replace the handle locks... install the head...and done!
align the rack and pinion gears, then position the new bracket on the column. replace the top collar ring and tighten the set screw, replace the handle locks... install the head...and done!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Bought a used drill press it was missing the table bracket assembly
John - April 5, 2016
Tool Type
Drill Press
Difficulty
Medium
Time
15-30 minutes
Tools Used
Wrench Set, Allen wrenches
Parts Used
Measured the column O.D. so I was sure I bought the right Part. While waiting for delivery I cleaned the column of rust and dings. On receiving the part, I removed the drill head. The head is pretty heavy, so make sure you are strong enough to press 50 lbs over your head!
Part slips over and down on the column and is bound in place with a locking handle. Replace the drill head and you are good to go!
Part slips over and down on the column and is bound in place with a locking handle. Replace the drill head and you are good to go!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Bracket Assembly casting partially broke away from the drill press post
Charles - February 3, 2016
Tool Type
Drill Press
Difficulty
Hard
Time
30-60 minutes
Tools Used
, allen wrenchs, 3 pound hammer
Parts Used
The standing drill press is heavy and awkward, so safety first. Its best to have two adults to do the steps laying down the drill press or picking it up with no kids or animals around and plenty of open floor space so as not to trip and making sure all body parts are clear of the drill press. Unplug the drill press. Carefully lay the drill press flat on the floor with wood blocks under the head. Loosen set screws holding the head on the post. Remove the drill press head from the post. This may require some effort and besure not to hit any cast iron directly with a hammer. Set the drill press without the head back virtically. Remove the raise/lower linear gear collar and linear gear along with the broken bracket assembly from the post. Insert the new worm gear and shaft into the new bracket assembly as well as the linear gear. Place the bracket assembly with the linear gear and worm gear engaged with the linear gear over and onto the post. Slide the assembly down until the linear gear rod inserts into its bottom slide slot. Now slide the linear gear collar over and onto the post and into position over the linear gear and tighten the collar's set screw. There should be enough play between the collar and bottom slide slot to permit freedom of rotation for the bracket assembly. Lay the post assembly back on the floor and insert the post back inside the the drill press head. Ensure the post is all the way inside the head. Tighten the set screws on the head to firmly attach it to the post. Carefully reposition the drill press virtically and then loosen the head set screws on the head holding it firmly on the post. Align the head with the Post base plate and retighten the head set screws. Now place the worm gear crank on the worm gear shaft that should be sticking out of the bracket assembly and tighten its set screw. Place the drill press table back in its slot on the bracket assembly. Plug the drill press back in and you should be ready to go.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
