Medium
15-30 minutes
This item has been sourced from the original manufacturer to be used with miter saws from Makita. The slide plate connects to the base assembly. This item fits between the table and the base to provide spacing and to allow the table to pivot easily. This part is priced as a single item, please note three slide plate may be needed.
Slide Plate ( 3 Pcs Required F 343799-7
OEM part for: Makita
Part Number: 343799-7
$3.99
In Stock
Ships within 1 business day 
Jump To:
Frequently Purchased Together ?
Compatibility
This Slide Plate ( 3 Pcs Required F will fit the following 8 machines. Confirm this part works with your model, and view the detailed model diagrams and repair help we have to offer.
Makita
Show More Compatible ModelsThis item works with the following types of products:
- Miter Saw Parts
- Saw Parts
Customer Part Reviews ?
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Slide Plate ( 3 Pcs Required F
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
miter table was difficult to move
Paul - July 28, 2017
👍 2 of 2 people found this instruction helpful
Tool Type
Miter Saw
Difficulty
Medium
Time
1-2 hours
Tools Used
Screwdriver, Socket set, Adjustable Wrench
1. Remove the 4 bolts that secure fence to the base, remove the fence.
2. Remove kerf board.
3. Remove handle.
4. Remove Center nut and bolt that secures table to the base.
5. Remove 2 Phillips screws that secure metal spring steel clip to miter table.
6. Separate saw and table from the base.
7. Remove damaged parts, and inspected base and miter table for cause of part failure.
8. Used 400 grit silicon carbide sanding belt remnant to smooth the surfaces that showed signs of wear, thoroughly cleaned surfaces with mineral spirits, wiped clean.
9.installed new slide plates (3) onto base, applied light coating of white grease to top side of slide plates.
10. Applied liberal amount of white grease to center hub of the miter table, set miter table onto the base, installed center bolt and nut.
11. Tightened center nut, do not over tighten, tighten the nut to the point where the table operates smoothly. Make sure that the miter table and base are firmly attached.
12. Installed new kerf boards.
13. Installed fence, make sure to square the blade to the fence.
14. Installed spring steel clip, screwed in handle.
15. Installed new carbon brush set.
16. Checked operation of tool.
2. Remove kerf board.
3. Remove handle.
4. Remove Center nut and bolt that secures table to the base.
5. Remove 2 Phillips screws that secure metal spring steel clip to miter table.
6. Separate saw and table from the base.
7. Remove damaged parts, and inspected base and miter table for cause of part failure.
8. Used 400 grit silicon carbide sanding belt remnant to smooth the surfaces that showed signs of wear, thoroughly cleaned surfaces with mineral spirits, wiped clean.
9.installed new slide plates (3) onto base, applied light coating of white grease to top side of slide plates.
10. Applied liberal amount of white grease to center hub of the miter table, set miter table onto the base, installed center bolt and nut.
11. Tightened center nut, do not over tighten, tighten the nut to the point where the table operates smoothly. Make sure that the miter table and base are firmly attached.
12. Installed new kerf boards.
13. Installed fence, make sure to square the blade to the fence.
14. Installed spring steel clip, screwed in handle.
15. Installed new carbon brush set.
16. Checked operation of tool.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Two of the slide plates were missing and the third was bent. The kerf boards were chewed up.
David - April 13, 2022
Tool Type
Miter Saw
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver, Socket set
1. Disassembled and cleaned everything.
2. Installed the slide plates.
3. Did the necessary lubrication points.
4. Reassembled the saw.
5. Tapped in the kerf boards.
2. Installed the slide plates.
3. Did the necessary lubrication points.
4. Reassembled the saw.
5. Tapped in the kerf boards.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Bent side plate causing saw not to turn properly.
Jerry - December 10, 2018
Tool Type
Miter Saw
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver, Pliers, Socket set
Parts Used
Read and followed instructions from your site of others. I found them to be very helpful and accurate.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Slide Plate 3 of them and Kerf Board
Lawrence - October 10, 2016
Tool Type
Miter Saw
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Socket set
Removed the turn base and put the new plate slides in there proper place and then I put the kerf board on and that is that
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
