Medium
30-60 minutes
This metal driver pulley is used in Murray lawn tractors. It is a replacement part directly sourced from the manufacturer. This part is sold as an individual replacement. The drive pulley applies force to the motion drive belt, which is wrapped around this part. A wrench and pliers may be needed for the replacement of the pulley when it becomes worn or cracked.
Pulley - Low Noise 95094MA
OEM part for: Murray
Part Number: 95094MA
$60.63
In Stock
Ships within 1 business day 
Jump To:
Frequently Purchased Together ?
Compatibility
This Pulley - Low Noise will fit the following 517 machines. Confirm this part works with your model, and view the detailed model diagrams and repair help we have to offer.
Murray
Show More Compatible ModelsThis item works with the following types of products:
- Lawn Tractor Parts
This part replaces obsolete part #: 095094MA, 91807, 95094, MU095094MA
Customer Part Reviews ?
Average Rating (out of 5):
Click to filter by ratings:
5 stars
3
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
Worked as expected
Original Drive Pulley was worn out & beginning to wobble a bit, but after 23 years of service....what would you expect! New pulley works fine and I'm back to mowing again.
Guest -
May 11, 2022
Verified Purchase
Murry Drive Pully
Part came quickly, fit correctly, was good quality. Was not an easy repair, but that was fault of manufacturer, not the replacement part.
Guest -
May 11, 2021
Verified Purchase
Murray tractor parts
Always satisfied when ordering parts, must say hard to find parts. Understand situation we are all under now, must have a little patience on shipping time
Guest -
July 5, 2020
Verified Purchase
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Pulley - Low Noise
How big is the bor
Chambers
for model number 461007x92a
asked on 2023-05-06
Hello Chambers, thank you for your question. The information we could find on this drive pulley is it has ID: 5/8", ?OD: 8-1316", ?Width: 13/16", ?Keyway: 3/16. We hope this is of some help.
eReplacementParts Team May 06, 2023
Diminisions of this part
John
asked on 2022-09-19
Hello John, thank you for your inquiry. This drive pulley is approximately 9 1/4" L x 9 1/4" W. We are looking forward to hearing from you!
eReplacementParts Team September 19, 2022
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Mower would not move due to belt coming off a extremely worn transaxle pulley.
Robert - July 22, 2016
👍 19 of 19 people found this instruction helpful
Tool Type
Lawn Mower
Difficulty
Easy
Time
1-2 hours
Tools Used
Screwdriver, Pliers, Socket set, Wrench Set
Parts Used
After wasting time trying to put the belt back on the transaxle pulley I realized the pulley was trashed (the center hole was completely wallowed out) and I was missing the snap ring that holds the pulley at the proper height. I dropped the mower deck, jacked up the rear end placing jack stands under the mower and pulled off the rear wheels. Then I disconnected the brake and shifter rods and removed the 5 bolts securing the transaxle and lowered it on the jack. It was very easy to install the new snap ring and pulley. The belt was in great shape so I stayed with it. I bought a new pulley for the clutch and replaced it at the same time. While my pulley was ok I figured since it was only a little more than 10 bucks I'd change it out and I hope to be done with a future repair as the machine is 14 years old. Special instructions would be "you have to hold the clutch/brake pedal down while placing the drive belt" and don't forget to loosen those two rods that are supposed to keep the belt from coming off the drive pulley. They will keep you from putting a belt on if not slackened and moved away for placement.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Pulley had rusted away, so no drive system operation
Charles - June 27, 2016
👍 6 of 7 people found this instruction helpful
Tool Type
Lawn Tractor
Difficulty
Medium
Time
30-60 minutes
Tools Used
Pliers, Cuttoff Wheel, Pitman Arm Puller
1. Removed the axle from the tractor.
2. Cleaned/washed off the axle to remove dirt and debris.
3. Used 3 inch cutoff wheel and made a 2 inch square of pulley at the shaft area.
4. Used a 3" pitman/tie rod puller to remove the pulley collar and remains from the shaft.
5. Cleaned shaft and applied anti seize to the shaft.
6. Installed new pulley, snap ring.
7. Reinstalled axle and replaced belt.
2. Cleaned/washed off the axle to remove dirt and debris.
3. Used 3 inch cutoff wheel and made a 2 inch square of pulley at the shaft area.
4. Used a 3" pitman/tie rod puller to remove the pulley collar and remains from the shaft.
5. Cleaned shaft and applied anti seize to the shaft.
6. Installed new pulley, snap ring.
7. Reinstalled axle and replaced belt.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Old drive pulley was damaged.
Harry - November 7, 2017
👍 4 of 4 people found this instruction helpful
Tool Type
Lawn Tractor
Difficulty
Medium
Time
30-60 minutes
Tools Used
Pliers, Socket set
Parts Used
1. Removed the battery.
2. Took the back plate off the mower.
3. Loosened four bolts holding the rear assembly to the mower.
4. Lifted the mower off the rear assembly.
5. Replaced the old drive pulley with the new.
6. Replaced the lock washer.
7. Reattached the belt.
8. Reattached the rear assembly and the rear plate.
9. Replaced the battery.
2. Took the back plate off the mower.
3. Loosened four bolts holding the rear assembly to the mower.
4. Lifted the mower off the rear assembly.
5. Replaced the old drive pulley with the new.
6. Replaced the lock washer.
7. Reattached the belt.
8. Reattached the rear assembly and the rear plate.
9. Replaced the battery.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Some how the collar on the pulley got damaged destroying the keyway. I had to replace both items to get the lawnmower to stop making noises
Russell - April 14, 2016
👍 3 of 3 people found this instruction helpful
Tool Type
Lawn Tractor
Difficulty
Easy
Time
30-60 minutes
Tools Used
, Snap ring pliers
Parts Used
The transmission had to be removed from the lawn mower, it was easy only 4 small screws held it to the frame. The pulley was held on the shaft by a snap ring.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Lower e-ring missing ,drive pulley bad
jack - April 14, 2017
👍 1 of 1 people found this instruction helpful
Tool Type
Lawn Tractor
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Pliers, Socket set, Wrench Set
Drop rear end, removed retaining ring, removed old pulley put e-ring in place put on new pulley put new retaining ring reinstalled rear end and drive belt.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Hole in pulley wollered out.
Phil - November 9, 2020
Tool Type
Lawn Tractor
Difficulty
Easy
Time
15-30 minutes
Tools Used
Adjustable Wrench, Hammer
C
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Drive pully rusted out... belt wont stay on
Justin - June 5, 2016
👍 1 of 2 people found this instruction helpful
Tool Type
Lawn Tractor
Difficulty
Hard
Time
More than 2 hours
Tools Used
Socket set, Wrench Set, Nutdriver, Air ratchet. Electric grinder
Parts Used
The drive pulley I ordered for my old hand me down Murray riding lawn mower was a perfect fit . It was a certified Briggs and Stratton part. Which Murray has been out of business for years so when i called around I was told Murray parts have been discontinued. The other review for this part said only 4 bolts to drop the transmission and mount Pulley. Not true on my model.....some of the bolt locations were very difficult to loosen. So taking the battery out and removing the rear tow plate made it possible. I broke one old rusty bolt and the pulley snap ring and shaft had become one with rust...due to the fact it sat outside for 5 years. I had to cut the pulley into quarters like a pie with a grinder cutting wheel to remove from shaft. I created a snap ring using a zinc washer. The good news was that the pulley fit perfectly snug and the mower is running smoothly now with new drive pulley and belt. !!!! I couldn't be more satisfied...35 dollars total ( included shipping) I hope your machine isn't as rusty as mine good luck !
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
