Drill Parts
We sell only genuine OEM parts.
OR
Popular Drill Product Types
See All
Popular Drill Parts
- Manufacturer Part Number:
- 330072-98
Length: 8'
Gauge: 18
Wires: 2
Type: Bare Wire
This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the new cord wires to go correctly into wire terminals also rou...
- Manufacturer Part Number:
- CB440
The brush box kit fits a variety of cordless gardening tools. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder. Due to friction, carbon brushes are common replacement parts. If the functioning of your motor changes and does not work, then check if the brush is worn out or inspect the wire lead for cracks, burns and other damage. Replacing the b...
- Manufacturer Part Number:
- N918736
This cord protector is a genuine DeWalt replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.
- Manufacturer Part Number:
- 22-18-0702
Original Milwaukee replacement part. This Brush is sold individually, most repair jobs will require Two (2) of this item. As pictured, this brush is ready to install and includes carbon brush, wire lead, and spring. Over time, brushes will wear down and eventually require replacement. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear...
- Manufacturer Part Number:
- 664064-4
Length 8 Foot
Length: 6'
Gauge: 18
Wires: 2
Type: Bare Wire
This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individually. It comes with a rubber sleeve grommet that is not sol...
- Manufacturer Part Number:
- 176846-04
This carbon brush is an authentic DeWalt replacement part. It is sold individually, 2 are needed to make a set • Worn brushes are frequently the cause of a poorly running motor. • Replacing brushes can fix an intermittently operating motor. • New brushes can restore a motor's electric braking. Carbon motor brushes are one of the most commonly replaced power tool parts. The reason is that c...
- Manufacturer Part Number:
- CB407
This set includes 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that's operating intermittently. • New b...
- Manufacturer Part Number:
- 901266
This is a genuine Porter Cable replacement part, it is sold individually. A Cord Strain Reliever is used on most all power tools. It purpose is to reduce the bending of the cord as it comes out of the housing, which otherwise would cause the cord to crack and wear.
- Manufacturer Part Number:
- CB75
- Manufacturer Part Number:
- 183E34-9
- Manufacturer Part Number:
- 45-06-0635
This is a Genuine Manufacturer Sourced replacement part designed for use with Milwaukee Drills. This part is made out of Metal and Rubber Material. This part provides a seal for Water Swivel Housing. There are Two (2) of these Seals on each end of Water Swivel Housing. Please note this item is Sold Individually.
To complete this repair you would need a Screwdriver and Pliers.
- Manufacturer Part Number:
- 605040-20
This Ball Bearing has metal shielding on both sides. This is a genuine Dewalt replacement part that is sold individually. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. • Bear...