Cordless Drill Parts

$17.90

Manufacturer Part Number:: N413423

This OEM housing assembly in your impact driver is the protective outer casing that encloses the internal components of the tool, providing structural support. The assembly consists of both the top and bottom sides and it operates using a 20-volt battery. To identify if the housing assembly is broken, look for visible cracks, fractures, or loose components. Excessive vibration or unusual noises du...

Carbon Brush Set

★★★★★

(34)

$8.44

Manufacturer Part Number:: CB440

The brush box kit fits a variety of cordless gardening tools. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder. Due to friction, carbon brushes are common replacement parts. If the functioning of your motor changes and does not work, then check if the brush is worn out or inspect the wire lead for cracks, burns and other damage. Replacing the b...

Housing Set

★★★★★

(5)

$21.62

Manufacturer Part Number:: 183E34-9

Steel Ball

★★★★★

(18)

$6.15

Manufacturer Part Number:: N089668

Genuine Dewalt replacement part, this item is sold individually. The N089668 Steel Ball is part of the chuck assembly of the Impact Drivers shown below. When you pull back the sleeve of the chuck assembly and insert your bit, the Steel Ball is the part that locks the bit in the chuck assembly.

Compression Spring

★★★★★

(7)

$5.16

Minimum Quantity of 2 required

Manufacturer Part Number:: N019351

This is an OEM authorized part. It is sold individually. This spring maintains pressure on the N078437 Sleeve, and the rest of the bit holder assembly, to keep the bit in the holder. If this part fails the bit cannot be held in the bit holder. It is commonly used in impact drivers, and is compatible with the impact drivers listed below.

Keyless Chuck

★★★★★

(15)

$32.57

Manufacturer Part Number:: 42-66-2608

This 1/2" keyless chuck is a high quality item designed for use with Milwaukee drill drivers. It is a genuine part that is sourced directly from original equipment manufacturer. This keyless chuck allows user to secure a drill bit without the need for any tools while the ratcheting action clicks the jaws tightly into place for reduced bit slippage. If your drill's bit retention is suffering or the...

Spring

★★★★★

(5)

$4.13

Minimum Quantity of 2 required

Manufacturer Part Number:: N437890

This is a spring designed to fit within the bit holder assembly of an impact driver, also known as an impact wrench. Positioned between the anvil and ring gear, this spring is accompanied by a washer and hog ring on each side to provide tension and maintain consistent pressure on the inserted bit within the holder. As a high-wear component, this spring will eventually wear out, resulting in a less...

Brush Card Assembly

★★★★★

(11)

$15.73

Manufacturer Part Number:: 22-22-2602

This OEM sourced replacement part is designed for Milwaukee drills/drivers. This assembly secures carbon brushes around the armature to provide stable contact. This assembly consists of: plastic holder ring, four (4) metal brush holders with springs and four (4) carbon brushes with lead wires attached. To replace this assembly you would need a screwdriver. • First remove screws holding the cov...

Retaining Ring - Ext

★★★★★

(1)

$5.37

Minimum Quantity of 2 required

Manufacturer Part Number:: 34-60-0725

This external retaining ring, also known as a snap ring or circlip, is supplied by the original manufacturer for use in impact drivers. It helps to secure the collar in the front housing assembly. It should be replaced if it is lost, damaged, or no longer able to remain securely attached. To replace the retaining ring, disassemble the front housing assembly and pull out the ring. Position the new ...

Motor Assembly

★★★★★

(5)

$19.67

Manufacturer Part Number:: 23-30-0650

This is an authentic replacement part manufactured for use with Milwaukee ratchets. The motor assembly is used to power the ratchet and it the motor includes the gear that drives the planet gears. This motor assembly is available as an individual replacement part.

Reversing Drive Assembly

★★★★★

(2)

$139.71

Manufacturer Part Number:: 14-72-0110

It is a genuine manufacturer-supplied part which is designed for use with Milwaukee drills. This special reversing drive assembly allows a user to operate the tool at an angle. It is an identical replacement for a damaged or a missing component that was included with a new unit. To ensure the correct application, please refer to the owner's manual for your model. One durable metal reversing drive ...

Carbon Brush And Holder Set

★★★★★

(18)

$17.93

Manufacturer Part Number:: N031214

This is a genuine Dewalt replacement part, it is sold in a set of two. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that's operating intermittently. • New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items,...

Popular Cordless Drill Brands

Popular Cordless Drill Parts

Popular Cordless Drill Models

All Cordless Drill Brands

Shop by Popular Cordless Drill Part Types

Cordless Drill Parts

Search By Model or Part Number

Popular Cordless Drill Brands

Popular Cordless Drill Parts

Popular Cordless Drill Models

All Cordless Drill Brands

Shop by Popular Cordless Drill Part Types