Genuine Black and Decker replacement part, this item is sold individually. This part is placed underneath the Hex Nut that holds the blade to the shaft on the mowers shown below. It helps secure the blade to the shaft assembly on the mower.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Mower blade spacer
The spacer worked fine.
Guest - June 4, 2019
Verified Purchase
★★★★★
★★★★★
Worked as expected
The parts came promptly and were correct and worked as expected. The site video showed how to install. I would recommend this site to buy replacement/ repair parts.
Guest - May 19, 2020
Verified Purchase
★★★★★
★★★★★
Great service
I’ve used you for the parts I need while rebuilding my B&D mower and even thru covid-19 I feel you were professional and quick with my orders, thank You!
Thomas
Thomas - May 27, 2020
Verified Purchase
★★★★★
★★★★★
Black & Decker electric mower parts
The parts worked fine, quick shipping, thanks
Stanford - June 1, 2020
Verified Purchase
★★★★★
★★★★★
work as expected
arrived before promised
ROBERT - June 3, 2020
Verified Purchase
★★★★★
★★★★★
Exactly what I needed!
My lawnmower works again!
Guest - September 5, 2022
Verified Purchase
Customer Repair Instructions
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Easy
Less than 15 mins
(33 rated repairs)?
< Prev
1
2
3
Next >
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Last summer I took the blade off to sharpen. I didn\'t give enough attention on how the items on the blade/fan shaft went back together, which resulted with the blade not being secure, and untimely being out of balance, which damaged the fan. I decided to replace everything on the blade/fan shaft.
Starting closest to the mower, I r
... Read moreeplaced the Spacer, no problem there. Next was the Fan, once again, no problem. Followed by the Blade, and it tells you what side should face the ground written right on it. Now, this is the point where you need to pay attention. What is next is called an Insulator followed by another spacer. The insulator has ridges on each side of it, that will straddle the blade on one side, and the metal spacer on the other side. Each have a oval hole in the center and you need to make sure each is pushed far enough on to the shaft to fit snugly on the oval part of the shaft. The tricky part for me was to keep everything lined up and inside of the ridges, plus keeping everything pushed up on the shaft to expose the threads for the Hex Nut to get started. Once the Hex Nut is started, the only thing you need to do at that point is to make sure everything stays lined up as you tighten the Hex Nut. As you tighten Hex Nut, and the blade and insulator and the metal spacer become not aligned, loosen the Hex Nut enough to get everything back in line and start tightening again. Hope this helps.
Read less
Did you find this story helpful?
Thank you for voting!
Parts were lost when trying to use a thatcher blade. The vibration loosened the retainer nut and parts were lost in the grass.
Remove the blade nut, then the blade spacer, then the blade insulator. Remove the old blade and install the new one, then install the new insulator, spacer and tighten the blade nut
Did you find this story helpful?
Thank you for voting!
Nothing was wrong at all. It worked right the first try
1. Used Channel Lock pliers to hold the spacer
2. Turned the hex nut counter clockwise to loosen and remove the hex nut.
3. Removed all of the old parts.
4. Replaced old parts in the same order with the new parts
5. Gripped the spacer with the channel lock pliers.
6. Tightened the hex nut till tight.
Did you find this story helpful?
Thank you for voting!
Old flap tore off. Old spacer and insulator were stripped
I had taken blade off to sharpen with difficulty as the small parts were worn. The flap had previously torn off. So flap just slides in the grooves no tools needed, except a mallet to get old piece out. For blade re installation just a 3/4 ratchet sure pieces are in correct order
Removed old blade and parts and inserted new ones. Tightened the new nut. I had not tightened it enough and blade became loose while moving. I had not replaced the spacer correctly so I took everything off and retightened. This time it worked. However, I am now convinced that I should just give an eye inspection to the mower before I star
... Read moret it.
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
