This is genuine Shindaiwa replacement part, it is sold individually. The air filter is placed in the Cleaner Body, then the Cleaner Cover is placed over it. The purpose of the Air Filter is to keep debris and contaminants from entering the carburetor and engine. You should inspect the filter from time to time, to make sure it is clean or if it is time to replace it.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Just like the Original
Great OEM part and outstanding service from e-replacement parts. I've ordered several parts from ERP and their selection and service is second to none. Will continue to rely on them for all my parts needs
Guest - September 24, 2019
Verified Purchase
★★★★★
★★★★★
Great price
The price for the part was great, hard to find older machine parts and when I do they are often overpriced. Thanks.
Guest - June 23, 2020
Verified Purchase
★★★★★
★★★★★
Perfect fit!
As always ereplacment getting me exactly what I need! I actually order about 20parts and rebuilt my 15yr old shindaiwa. It’s literally impossible to find pars for it here on maui. Mahalo!
Guest - December 9, 2020
Verified Purchase
★★★★★
★★★★★
Super Parts Great Prices
I have been using eReplacment for a few years now. Love the web site and the ease of finding the correct parts for small engine equipment. Will be using them again when I need parts of my stuff!
Greg - April 26, 2021
Verified Purchase
★★★★★
★★★★★
Perfect fit every time
Finally I found a source for factory replacement parts for my Shindawa T-270 trimmer.
Glen - July 5, 2021
Verified Purchase
★★★★★
★★★★★
Exactly what I needed!
Fast shipping and the parts fit perfect!
Craig - November 16, 2021
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Took off air filter ,carburetor and fuel pipe kit. Replaced with new parts. Hardest part was the fuel pipe kit. Rubber that goes into the gas tank was little bigger then the original. I had to go with my drill and make the hole a little bigger. Otherwise it was a easy fix. I had my t270 shindaiwa trimmer over 10 years and it works like ne
... Read morew.
Just make sure that all of your new parts are laid out separately, in order to allow you to keep everything separate from the old parts that you will be removing. Take your time, clean areas and parts that you will be keeping as you go. Once all parts have been removed and parts cleaned, work your way backwards from the way you removed pa
... Read morerts when installing the new parts. I use 90 degree type Allen Head wrenches without handles that way I do not over tighten fasteners. I had gasket material that stuck on me around the intake portal to the piston that needed to be scrapped off, so I brought the piston to TDC and stuffed a small bit of rag in the hole to keep debris from getting inside the head.
I also bought from a local store a replacement muffler and muffler bolts and gasket that was installed during this time as well, but the store did not have the other parts I was needing.
EVERY part that I ordered from eReplacement Parts fit exactly as the old parts, I did not have to make any adjustments to the new parts to get them to fit.
When I was finished, I primed the carburetor, adjusted the choke and slid the on/off button to on, and pulled the cord one time and it fired right up. I adjusted the choke and set it down and let it idle as I put my tools up and cleaned up the area I was working in.
I am very happy with my whole experience dealing with eReplacement Parts. I will be ordering again from them.
Read less
Did you find this story helpful?
Thank you for voting!
throttle cable \"stiff\" and would not return to idle.
Loosen two screws on throttle lever assy, loosen two screws on power head-to-trimmer tube clamp. Twist and slide power head off tube. Coated new grip inside with silicone spray and slide onto tube. Slide power head onto shaft and engage drive shaft, retighten clamp screws. Install new cable and spring. NOTE: found it best to route new cab
... Read morele and kill wires thru new grip channel before sliding new grip onto shaft! Also clean and lube anything that needs attention during tear-down always makes reassembly much easier.
Read less
Did you find this story helpful?
Thank you for voting!
Clutch shoes completly worn out and spring had pulled through the holes.
1. Removed the shaft from the engine.
2. Removed the clutch housing.
3. Unbolted the old clutch assembly.
4. Cleaned the unit and reassembled.
5. Fuel filter I ordered turned out to be for an echo product, so just cleaned the Shindaiwa fuel filter.
6. Gasket was for the gas cap.
7. Worked great when re
... Read morepair was finished. I just love buying professional grade equipment, it really makes a difference.
I took all parts off like carb and I put them all back exact replacement parts went on really well adjusted the idle screw to old carb level cranked first pull
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
