Easy
15-30 minutes
It is a genuine manufacturer-sourced component which is specially designed for use with Bostitch nailers. This is an identical replacement for a missing or a faulty movable nose piece that was originally installed on a new unit. It is the part that helps to push the nail. Please make sure to check the owners manual and the appropriate diagram of your model for the correct location and application of this part. Keep in mind this high-quality nose is made of durable metal and is sold individually.
Nose,movable 9R209479
OEM part for: Bostitch
Part Number: 9R209479
$14.34
In Stock
Ships within 1 business day 
Compatibility
This part will fit the following 4 machines
Bostitch
MCN250S Metal Connector Nailer View Diagrams & Manuals
MCN250 Metal Connector Nailer View Diagrams & Manuals
MCN250 (Type 0) Met Conn Nailer Power Tool View Diagrams & Manuals
MCN250S (Type 0) Met Conn Nailer Power Tool View Diagrams & Manuals
This item works with the following types of products:
- Nailer Parts
This part replaces obsolete part #: 175573
Repair Videos ?
Watch the Repair Video for
Nose,movable
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Nose,movable
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Movable nose on Bostitch MCN 250 positive placement was fractured causing difficulty aligning the nails and firing nails
Mark - March 13, 2017
👍 2 of 2 people found this instruction helpful
Tool Type
Nailer
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, 3 mm bit wrench
Parts Used
1. Disconnect nail gun from air source.
2. Use a small flat head screwdriver to pry loose the 2 round plastic retainers that help keep the plastic movable nose cover in place.
3. Use the same small flat head screwdriver to pry the two plastic "legs" off of the two pins from which the plastic retainers were removed and then remove the plastic nose cover away from the nailer while sliding the cover in the direction of the tip of the nailer (some bending of the flexible plastic cover is required).
4. Remove the inhex (allen) bolt (3mm head) which attaches the movable nose to the nailer being careful not to lose the coil spring and noting the position of the spring (large opening vs. small opening in coil spring) and the "t" piece of the movable nose.
5. Replace the movable nose being careful to properly orient the coil spring, install and tighten the allen bolt, install the plastic cover being careful to pry to "legs" up over the locating pins and push on the two round plastic retainers.
6. Don your safety glasses, attach air hose and test fire nailer into wood surface.
7. Congratulate yourself on a job well done and vow to accurately place all nails in the connector nail hole to prevent fracturing the movable nose again.
2. Use a small flat head screwdriver to pry loose the 2 round plastic retainers that help keep the plastic movable nose cover in place.
3. Use the same small flat head screwdriver to pry the two plastic "legs" off of the two pins from which the plastic retainers were removed and then remove the plastic nose cover away from the nailer while sliding the cover in the direction of the tip of the nailer (some bending of the flexible plastic cover is required).
4. Remove the inhex (allen) bolt (3mm head) which attaches the movable nose to the nailer being careful not to lose the coil spring and noting the position of the spring (large opening vs. small opening in coil spring) and the "t" piece of the movable nose.
5. Replace the movable nose being careful to properly orient the coil spring, install and tighten the allen bolt, install the plastic cover being careful to pry to "legs" up over the locating pins and push on the two round plastic retainers.
6. Don your safety glasses, attach air hose and test fire nailer into wood surface.
7. Congratulate yourself on a job well done and vow to accurately place all nails in the connector nail hole to prevent fracturing the movable nose again.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
