Hex Cap Screw

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Socket set

Worn blade bolt and cracked adapter.

Remove the spark plug wire. Then remove the worn blade bolt, blade support and blade. The cracked adapter came right off of the spindle. I wiped the spindle clean. Then line up the key in the adapter with the slot in the engine shaft. Then put on the blade, the support and the new blade bolt on. Then plug the spark plug wire back in.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used:

Blade - 942-0741A

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Power Drill, Socket set, Screw extractor

Hex bolt broke

1. Use screw extractor to remove severed bolt
2. Install blade and new hex bolt

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Socket set, Wrench Set

Loose blade!

Unplugged spark plug
Removed old blade and support and adapter
installed all new parts
Reinstalled sparkplug wire to sparkplug
Done!

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used:

Blade Adapter - 687-02220

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Socket set, None

Blade support worn

Tilt mower up remove blade take off plastic cover two bolts, should order the bolts they get rusty. Slide belt off pulley as you pull down part reinstall easy

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Socket set

Old Bell Blade Support had Broke

Replaced Old Hex Cap Screw and Bell Blade Support with New One, Torqued Tight with Socket Wrench!

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used:

Repair Difficulty:

Medium

Time Spent Repairing:

15-30 minutes

Tools Used:

Power Drill, Socket set, Easy out and drill bit

Blade attachment bolt had broken

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used:

Blade Adapter - 687-02220

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Socket set, Wrench Set

Blade adp. was bent and blade would not stay tight

Removed old blade adp. Cleaned shaft. Slid belt on new blade adp. Installed new blade adp. held blade in place, added new blade bell support and new hex nut. And Presto Changeo, everything works great. All the parts fit just like the old ones, except the new ones work much better. Thanks for your help!

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used:

Standard Mulching Blade (21-Inch) - 942-0741A

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers, Socket set, Wrench Set, Hammer, pulley remover (press type)

Hit drainage culvert metal pipe and bent the bell blade support and the blade.

1. Removed the blade holding bolt.
2. Removed the blade adapter.
3. Removed the blade.
4. Pulled the bell blade support with a specialty tool.
5. Installed the new parts in the opposite order.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used:

Wave Washer - 936-0447

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Socket set

Bell blade support was cracked

Take out blade screw and related parts replace with the new ones changed all parts that hold the blade in place didn't replace blade because I had just sharpened it.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used: