Easy
15-30 minutes
Gasket-cap 104-1014
OEM part for: Jenny
Part Number: 104-1014
$4.99
Usually ships in 7 - 12 business days
Leaves our warehouse within 7 - 12 business days
Compatibility
This part will fit the following 4 machines
Jenny
J Series Four Cylinder Single Stage Stroke Pump View Diagrams & Manuals
JU Series Four Cylinder Single Stage Stroke Pump View Diagrams & Manuals
W Series Four Cylinder Two Stage Stroke Pumps View Diagrams & Manuals
WU Series Four Cylinder Two Stage Stroke Pumps View Diagrams & Manuals
This item works with the following types of products:
- Pump Parts
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Gasket-cap
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Bad unloader valve and found crank bearing was terminal
R.D. - December 24, 2015
Tool Type
Compressor
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Socket set, Wrench Set, Adjustable Wrench, Heat gun. ladysfoot bar
Repair was simple. Remove two air lines from Compresor heads and unloader housing. Loosen jam nut on unloader valve, unscrew unloader valve, watch for brass pin it will fall out if not careful. Remove four bolts that hold unloader assem. housing to compressor. Using screw driver and a ladyfoot bar carefully pry housing from compressor. It will be very tight do not pry one dircetion or the other to far, crank bearing is held in place within housing. The housing is the outer bearing support surface. Once housing is off remove unloader assem. from crankshaft. Remove very small cotter pin at back of unloader assem. With that out of the way use a small gear/bearing puller to remove main shaft bearing from crankshaft. Note that old bearing has a glue /locktite on outer surface.
Clean gasket surface at this time. Also clean the unloader assem. and housing to remove any metal filings and or dirt. Now is a good time to drain the oil and replace with new when everytihng is back together.
Install new bearing by way of correct bushing/ sleeve of correct diameter ( I used a 3/4 inch drive 1 1/4 socket) of inside of bearing. Warm bearing with heat gun to allow for metal to expand you may not think this is enough heat but it will make for an easy install. Place bearing on crank shaft, place block of wood behind crank area in which the bearing will be. Using the correct dia. sleeve, drive new bearing on to crank tapping carefully, do not twist bearing on shaft it will be impossible to get on, drive it straight. Make sure bearing is fully seated at flange on crank.
Reverse the removal process to assemble. Be careful when placing the unloader housing back on, the bearing does fit inside the housing , it too needs to be driven on straight.
Adjustment of the unloader valve, I found, was trial and error. Finally made adjustment with compressor running to get the valve to stay closed.
Clean gasket surface at this time. Also clean the unloader assem. and housing to remove any metal filings and or dirt. Now is a good time to drain the oil and replace with new when everytihng is back together.
Install new bearing by way of correct bushing/ sleeve of correct diameter ( I used a 3/4 inch drive 1 1/4 socket) of inside of bearing. Warm bearing with heat gun to allow for metal to expand you may not think this is enough heat but it will make for an easy install. Place bearing on crank shaft, place block of wood behind crank area in which the bearing will be. Using the correct dia. sleeve, drive new bearing on to crank tapping carefully, do not twist bearing on shaft it will be impossible to get on, drive it straight. Make sure bearing is fully seated at flange on crank.
Reverse the removal process to assemble. Be careful when placing the unloader housing back on, the bearing does fit inside the housing , it too needs to be driven on straight.
Adjustment of the unloader valve, I found, was trial and error. Finally made adjustment with compressor running to get the valve to stay closed.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
