Medium
30-60 minutes
This is an genuine Tanaka part that is specially designed for use with handheld lawn and garden equipment. It is used to filter out dust and debris from contaminating the engine. This foam filter element is sold individually. Please note, the filter cover and the base are both sold separately.
To replace this filter you should only need a screwdriver.
• Make sure to disconnect the spark plug
• Remove the cover screw
• Take off the cover and replace the filter element
• Reassemble and test the unit
Cleaner Element 6690362
OEM part for: Tanaka
Part Number: 6690362
$5.19
Usually ships in 7 - 12 business days
Leaves our warehouse within 7 - 12 business days
Jump To:
Product Description ?
- Classification: Part
- Weight: 0.01 lbs.
- Shipping: Ships Worldwide
Frequently Purchased Together ?
Compatibility
This part will fit the following 29 machines
Tanaka
DR-270PN Extended Reach Pole Saw View Diagrams & Manuals
TPS-270PN Extended Reach Pole Saw View Diagrams & Manuals
TPS-2510 Extended Reach Pole Saw View Diagrams & Manuals
TPS-270PF Extended Reach Pole Saw View Diagrams & Manuals
TPE-250 Portable Edger View Diagrams & Manuals
TPE-2510 Portable Edger View Diagrams & Manuals
TPE-270PF Portable Edger View Diagrams & Manuals
TPE-270PN Portable Edger View Diagrams & Manuals
TPH-270PF Articulating Pole Hedge Trimmer View Diagrams & Manuals
TPH-270PN Articulating Pole Hedge Trimmer View Diagrams & Manuals
TBC-250 Grass Trimmer / Brush Cutter View Diagrams & Manuals
PF-2600 Utility / Scooter Engine View Diagrams & Manuals
Wet Screed (After S/N P211651) Weber Vibrating Wet Screed Engine View Diagrams & Manuals
Wet Screed (P211650 & Lower) Weber Vibrating Wet Screed Engine View Diagrams & Manuals
TBC-220 Grass Trimmer / Brush Cutter View Diagrams & Manuals
TBC-220SS Brush Cutter View Diagrams & Manuals
TBC-2510 Grass Trimmer View Diagrams & Manuals
TBC-270PFD Brush Cutter View Diagrams & Manuals
TBC-270PN Low Emission Grass Trimmer / Brush Cutter View Diagrams & Manuals
TBC-265 Brush Cutter View Diagrams & Manuals
TBC-270PND Brush Cutter View Diagrams & Manuals
TBC-265SS Brush Cutter View Diagrams & Manuals
TBC-270PF Low Emission Grass Trimmer / Brush Cutter View Diagrams & Manuals
TBC-300 Brush Cutter View Diagrams & Manuals
TBC-300SDH Grass Trimmer / Brush Cutter View Diagrams & Manuals
TBC-3010 Grass Trimmer / Brush Cutter View Diagrams & Manuals
Moby X (26cc) Bladez PowerBoard View Diagrams & Manuals
PB-SE801 (Moby-X26) BladeZ 26cc Gas View Diagrams & Manuals
TWS-250 24cc Screed Engine View Diagrams & Manuals
Show More Compatible Models
This item works with the following types of products:
- Pole Saw Parts
- Saw Parts
- Edger Parts
- Hedge Trimmer Parts
- Trimmer Parts
- Engine Parts
- Grass Trimmer Parts
This part replaces obsolete part #: 4460637C200
Customer Part Reviews ?
Average Rating (out of 5):
Click to filter by ratings:
5 stars
1
4 stars
0
3 stars
1
2 stars
0
1 stars
0
< PREV
- 1
Easy Peasy fix
Perfect replacement part!
Guest -
August 26, 2022
Verified Purchase
Waited
The parts part was excellent. The wait time in this day and age was bad. The tracking showed it sat for 3 days before getting to USPS. Good thing I didnt need the parts asap.
Guest -
March 8, 2023
Verified Purchase
t
t
t -
t days ago
Verified Purchase
eReplacementParts Team
t
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Cleaner Element
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Fuel leaking from the tank
Mike - September 14, 2018
Tool Type
Pole Saw
Difficulty
Medium
Time
1-2 hours
Tools Used
Screwdriver, Pliers
0. Remove the remaining fuel from the tank. Using a funnel I put the fuel back into my 1 gallon gas can.
1. Removed the air cleaner cover.
2. Removed the hardware holding the tank in place.
3. Disconnect the fuel lines at the carburetor and primer, paying close attention to which line goes where.
4. Installed the new vent, return line and fuel line and filter into the new tank.
5. Removed the old primer and installed the new one.
6. Attached the new fuel lines to the correct places on the primer and carburetor.
7. Placed the new tank into position using the mounting bracket and screws attached the tank to the engine.
8. Filled the tank with fuel.
At this point I tried to start the saw, it would not start. I found that I had flooded the carburetor when I was checking the operation of the new primer.(guess I primed it one to many times!) Removed the spark plug then, using compressed air I dried the inside of the cylinder and the spark plug, reassembled and started the saw.
9. Installed the new air cleaner I had purchased and reinstalled the air cleaner cover.
10. Put the saw back to work trimming trees.
1. Removed the air cleaner cover.
2. Removed the hardware holding the tank in place.
3. Disconnect the fuel lines at the carburetor and primer, paying close attention to which line goes where.
4. Installed the new vent, return line and fuel line and filter into the new tank.
5. Removed the old primer and installed the new one.
6. Attached the new fuel lines to the correct places on the primer and carburetor.
7. Placed the new tank into position using the mounting bracket and screws attached the tank to the engine.
8. Filled the tank with fuel.
At this point I tried to start the saw, it would not start. I found that I had flooded the carburetor when I was checking the operation of the new primer.(guess I primed it one to many times!) Removed the spark plug then, using compressed air I dried the inside of the cylinder and the spark plug, reassembled and started the saw.
9. Installed the new air cleaner I had purchased and reinstalled the air cleaner cover.
10. Put the saw back to work trimming trees.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Air cleaner needed replacement
Russell - July 14, 2018
Tool Type
Trimmer
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver
Parts Used
Removed air cleaner cover.
Took old air cleaner element out.
Cleaned air cleaner body
Inserted new air cleaner element and replaced cover
Took old air cleaner element out.
Cleaned air cleaner body
Inserted new air cleaner element and replaced cover
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Used equipment given to me without air cleaner parts.
Jerry - December 10, 2016
Tool Type
Pole Saw
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
Placed the air filter in its place
Screwed the air cleaner cover with a the screw
Screwed the air cleaner cover with a the screw
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Air filter body broken.
jim - June 23, 2016
Tool Type
Trimmer
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Pliers
Removed air filter cover. Unscrewed everything down to the carburetor. Replaced everything after a thorough cleaning. All parts came as ordered, on time, and fit perfectly.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
