Medium
30-60 minutes
Carburetor Kit
- Part Type: Carburetor
Carburetor Kit 49-916
OEM part for: Oregon, Husqvarna, Toro
Part Number: 49-916
$8.00
Usually ships in 7 - 12 business days
Leaves our warehouse within 7 - 12 business days
Jump To:
Product Description ?
- Classification: Part
- Weight: 0.01 lbs.
- Shipping: Ships Worldwide
Frequently Purchased Together ?
Compatibility
This Carburetor Kit will fit the following 792 machines. Confirm this part works with your model, and view the detailed model diagrams and repair help we have to offer.
Husqvarna
Toro
Show More Compatible ModelsThis item works with the following types of products:
- Engine Parts
- Snowblower Parts
- Lawn Mower Parts
- Lawn Tractor Parts
This part replaces obsolete part #: 631021
Customer Part Reviews ?
Average Rating (out of 5):
Click to filter by ratings:
5 stars
3
4 stars
2
3 stars
0
2 stars
0
1 stars
1
< PREV
- 1
Simple rebuild
Installed new carb parts, they fit perfectly. Snow blower started on second pull and ran as good as new.
Guest -
March 4, 2023
Verified Purchase
Good quality
Arrived quick
Rich -
December 13, 2022
Verified Purchase
Easy repair
Part arrived quickly, repair went well and snowblower works great.
Guest -
February 14, 2020
Verified Purchase
All good to go
Hard to romance a rebuild kit, not always are they of good quality and the correct parts. This kit was of fine quality and all the correct components. I have noticed however, gasket kits are not as commonly placed, if a reseller packaged a rebuild carb kit with all the gaskets encountered removing the carb, I think youd have something. You never know if the gasket is going to survive the removal process, and if the kit already came with them, I dont see any push back, itd obviously have a higher cost, but the fact they are included would be a plus offer them both, with and without all gaskets watch what happens ;)
Mark -
January 18, 2023
Verified Purchase
ok except for one item
Received kit in a timely manner and machine is running ok with the new parts but the gasket for the bowl retaining bolt was too small and I had to use the old on.
Guest -
November 28, 2019
Verified Purchase
would run unless on full choke
Arrived in good condition. did not fix problem. purchased new carb which did fix problem of only running on full choke.
Guest -
November 8, 2022
Verified Purchase
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Carburetor Kit
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Did not stay running
Brandon - January 28, 2016
👍 7 of 10 people found this instruction helpful
Tool Type
Snowblower
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Pliers, Socket set
Parts Used
1. Take plastic cover off.
2. Take gas line off.
3. Unscrew bolt on bottom of carburetor.
4. Carefully pull pin on float watch for small spring it will fly.
5. Remove float and needle set aside.
6. Take a pick and remove rubber o ring were needle sits.
7. Install rubber o ring and needle also float.
8. Install rubber gasket for float bowl.
7. Screw bolt back in under float with gasket.
2. Take gas line off.
3. Unscrew bolt on bottom of carburetor.
4. Carefully pull pin on float watch for small spring it will fly.
5. Remove float and needle set aside.
6. Take a pick and remove rubber o ring were needle sits.
7. Install rubber o ring and needle also float.
8. Install rubber gasket for float bowl.
7. Screw bolt back in under float with gasket.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Float valve stuck in mostly closed position, engine would run rough with full choke only.
Arlen - December 15, 2015
👍 3 of 4 people found this instruction helpful
Tool Type
Snowblower
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Adjustable Wrench, n/a
Parts Used
I installed a fuel shutoff valve between the fuel tank and carburator a few years ago during a similar repair. If you don't have a shut off valve the fuel will spill out very quickly... either drain the fuel from the tank or turn the unit upside down before removing the float bowl. If fuel is dripping out of the vented fuel cap, you may want to drain the fuel tank.
There is a small torsion spring in the float hinge, take note of its orientation and be sure you reinstall it in the same orientation. It will fly out of its mounting when you remove the float hinge pin... make sure you don't lose the float spring. (Not included in the needle valve carb kit)
Assemble new float valve with valve clip and float into hinge mount, slide hinge pin part way, place hinge spring into position, then carefully slide hinge pin the rest of the way making sure the hinge pin goes thru the hinge torsion spring. Raise and lower the float and make sure the float needle valve is travelling to a closed and open position. The tab on the top of the float can be bent as an adjustment if needed.
Place gasket on carburator side seat, then install float bowl being creful not to damage the gasket. Install float bowl nut to snug + a little seating force.
There is a small torsion spring in the float hinge, take note of its orientation and be sure you reinstall it in the same orientation. It will fly out of its mounting when you remove the float hinge pin... make sure you don't lose the float spring. (Not included in the needle valve carb kit)
Assemble new float valve with valve clip and float into hinge mount, slide hinge pin part way, place hinge spring into position, then carefully slide hinge pin the rest of the way making sure the hinge pin goes thru the hinge torsion spring. Raise and lower the float and make sure the float needle valve is travelling to a closed and open position. The tab on the top of the float can be bent as an adjustment if needed.
Place gasket on carburator side seat, then install float bowl being creful not to damage the gasket. Install float bowl nut to snug + a little seating force.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Lawn Tractor Carburetor, was left with fuel in it for years.
Edward - November 4, 2017
👍 1 of 1 people found this instruction helpful
Tool Type
Lawn Tractor
Difficulty
Easy
Time
15-30 minutes
Tools Used
Wrench Set, Torx driver
Parts Used
Cleaned float bowl, the jets, and associated parts. Put the new rebuild kit on in the reverse order that they were removed.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Hard to start when cold
Jim - December 15, 2016
👍 1 of 1 people found this instruction helpful
Tool Type
Snowblower
Difficulty
Medium
Time
More than 2 hours
Tools Used
Screwdriver, Pliers, Socket set, Wrench Set, Nutdriver
Parts Used
Checked compression, tore down engine, replaced compression release, rebuilt carburetor, reassembled. It runs.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Chute would wobble Carb was loaded with gunk
Cal - December 10, 2015
👍 1 of 1 people found this instruction helpful
Tool Type
Snowblower
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Pliers, Wrench Set, Adjustable Wrench
Removed the old retainers & sand blasted the chute & painted it. Replaced all the chute retainers, plates & clip guard. Put marine grease around the bottom of chute & lubed all of the connections on the handle. Took off the carb soaked it in carb cleaner, cleaned & reassembled it.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
snow blower would not run
paul - December 27, 2021
Tool Type
Snowblower
Difficulty
Expert
Time
Less than 15 minutes
Tools Used
Wrench Set, Nutdriver
rebuilt carburetor and cleaned out old gas from tank made fresh gas
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Would not run. No fuel
Daniel - December 4, 2021
Tool Type
Snowblower
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Wrench Set, Adjustable Wrench, None
Motor wouldn’t even try to start. First, I just cleaned all the parts with carb cleaner and reassembled. It wouldn’t start. Second, I replaced some parts and cleaned everything again. No start. Third replaced more parts and cleaned everything. All parts in the carb were replaced. Now it runs. But not great. I’m unsure where the obstruction was.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Starter would motor, but not engage.
Ron - February 29, 2020
Tool Type
Snowblower
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Socket set, Wrench Set, Nutdriver
Parts Used
Replace grip rubber in drive pinion.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
General debris in gas lines and carb. Mice had built a nest under engine cover over the winter..
John - April 28, 2019
👍 0 of 1 people found this instruction helpful
Tool Type
Lawn Mower
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Pliers, Socket set
Removed air filter housing. Removed complete carb and intake. Cleaned everything with non chlorine brake cleaner. Removed carb bowl and cleaned. Replaced needle jet and gasket.
Replaced primer bulb which rots out every year, Replaced air filter. Cleaned gas tank.
Two primes, one pull, back in business.
Replaced primer bulb which rots out every year, Replaced air filter. Cleaned gas tank.
Two primes, one pull, back in business.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
